Войти:
Оценок - 1, средний балл: 4 ( )

Инструкция по эксплуатации Samsung, модель ML-2951ND

Производитель: Samsung
Размер: 10.94 mb
Название файла:
Язык инструкции:en
Фото и характеристики  Samsung  ML-2951ND
Перейти к скачиванию



К этому устройству также есть другие инструкции:

Фрагмент инструкции


2 2 The eight-digit PIN appears on the display. You need to enter the eight-digit PIN within two minutes to the computer which is connected to the access point (or wireless router). The messages are displayed on the display screen in the order below: a Connecting: The machine is connecting to the wireless network. b Connected: When the machine is successfully connected to the wireless network, the WPS LED light stays on. c AP SSID: After completing the wireless network connection process, the AP’s SSID information is diplayed on the LCD display. > Connecting in PBC mode 1 1 Press and hold the (WPS) button on the control panel for about 2 - 4 seconds until the status LED blinks quickly. The machine starts connecting to the wireless network. The LED blinks slowly for up to two minutes until you press the PBC button on the access point (or wireless router). 2 2 Press the WPS (PBC) button on the access point (or wireless router). a The light blinks fast on the WPS LED. The machine is connecting to the access point (or wireless router). b When the machine is successfully connected to the wireless network, the WPS LED light stays on. Wireless network setup 342. Using a network-connected machine >Connecting in PIN mode Re-connecting to a network Wireless network setup 342. Using a network-connected machine >Connecting in PIN mode Re-connecting to a network 1 1 The network configuration report, including PIN, must be printed. In ready mode, press and hold the (Cancel or Stop/Clear) button on the control panel for about 5 seconds. You can find your machine’s PIN number. 2 2 Press and hold the (WPS) button on the control panel for more than 4 seconds until the status LED stays on. The machine starts connecting to the access point (or wireless router). 3 3 You need to enter the eight-digit PIN within two minutes on the computer that is connected to the access point (or wireless router). The LED blinks slowly for up to two minutes until you enter the eight-digit PIN. The WPS LED blinks in the order below: a The light blinks fast on the WPS LED. The machine is connecting to the access point (or wireless router). b When the machine is successfully connected to the wireless network, the WPS LED light stays on. When the wireless function is off, the machine automatically tries to re-connect to the access point (or wireless router) with the previously used wireless connection settings and address. In the following cases, the machine automatically reconnects to the wireless network: • The machine is turned off and on again. • The access point (or wireless router) is turned off and on again. Canceling the connection process To cancel the wireless network connection when the machine is connecting to the wireless network, press and release the (Cancel or Stop/Clear) button on the control panel. You need to wait 2 minuites to re-connect to the wireless network. Wireless network setup 352. Using a network-connected machine Disconnecting from a network 1 Press the (Menu) button on the control panel. 352. Using a network-connected machine Disconnecting from a network 1 Press the (Menu) button on the control panel. To disconnect the wireless network connection, press the (WPS) button on the control panel for more than two seconds. • When the Wi-Fi network is in idle mode: The machine is immediately disconnected from the wireless network, and the WPS LED is off. • When the Wi-Fi network is being used: While the machine waits until the current job is finished, the light blinks fast on the WPS LED. Then, the wireless network connection is automatically disconnected. The WPS LED is off. ....Using the menu button Before starting, you will need to know the network name (SSID) of your wireless network and the network key if it is encrypted. This information was set when the access point (or wireless router) was installed. If you do not know about your wireless environment, please ask the person who set up your network. After completing the wireless network connection, you need to install a machine driver to print from an application (see "Installing driver over the network" on page 17). 2 2 Press Network > OK > Wireless > OK > WLAN Settings > OK. 3 3 Press the OK to select the setup method you want. • Wizard: The wireless network interface card in your machine searches for wireless networks in the area and shows the results. • Custom: You can configure the wireless settings according to your needs. Wizard mode 1 1 The wireless network interface card on your machine searches 2 2 for wireless networks in the area and shows the results. Press Search List > OK > select a the network > OK. 3 3 You can select a network using SSID. Press WLAN Security > OK > None > OK. If you see another message, go to the next step. 3636 Wireless network setup 4 4 According to the network you selected, the WLAN security encryption type will be WEP or WPA. •In case of WEP, press the Open System or SharedKey. -Open System: Authentication is not used, and Encryptio...

Эта инструкция также подходит к моделям:
Принтеры - ML-2950D (10.94 mb)
Принтеры - ML-2950DR (10.94 mb)
Принтеры - ML-2950ND (10.94 mb)
Принтеры - ML-2950ND/GOV (10.94 mb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории