Оценок - 4, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
This may be the result of the sheets characteristics, improper handling, unacceptable temperature and humidity levels, or other variables over which cannot be controlled. •Before purchasing large quantities of print media, ensure that it meets the specifications in this user’s guide and that it meets your output requirements. •Using print media that does not meet these specifications may cause problems, requiring repairs. Such repairs are not covered by the warranty or service agreements. The amount of paper put into the tray may differ according to media type used. (See "Print media specifications" on page 62.) •Using inflammable print media can cause a fire. •Use designated print media (See "Print media specifications" on page 62). The use of inflammable media or foreign materials left in the printer may lead to overheating of the unit and, in rare cases may cause a fire. Media sizes supported in each mode Mode Size Type Source Simplex printing For details about paper size, see "Print media specifications" on page 62. For details about paper type, see "Print media specifications" on page 62. Tray Duplex printing (Manual)a a.75 to 90 g/m2 (20~24 lbs bond) only (See "Print media specifications" on page 62). Letter, A4, Legal, US Folio, Oficio Plain, Color, Preprinted, Recycled, Bond, Archive Manual feeding in the tray Changing the tray size The tray is preset to Letter or A4 size, depending on your country. To change the size, you need to adjust the paper guides. 1Paper width guide 2Tray 3Paper length guide 1.Open front cover and pinch the paper length guide and pull it out to extend the tray. Because the machine is very light, it can move when you open and close the tray or install and remove the toner cartridge. Be careful not to move the machine when performing these tasks. 2.Flex or fan the edge of the paper stack to separate the pages before loading the paper. Insert the paper into the tray. 3.Load paper with the print side facing up. Make sure that all four corners are flat in the tray. Do not overload the tray with paper. Otherwise, it may cause paper jams. 4.Pinch the paper length guide to adjust the guide so that it is flush up against the rear edge of the paper; then pinch the paper width guides so they are flush against the sides of the paper. •Do not push the paper width guide too far causing the media to warp. •Do not use a paper with more than 6 mm (0.24 inch.) curl. •If you do not adjust the paper width guide, it may cause paper jams. Loading paper in the tray Tray 1.Open the front cover, pinch the paper length guide and pull it out to extend the tray. Then, adjust the tray size to the media size you are loading. (See "Changing the tray size" on page 28.) 2.Flex or fan the edge of the paper stack to separate the pages before loading papers. 3.Place the paper with the side you want to print facing up. When you print a document, set the paper type and size for the tray. For information about setting the paper type and size on the control panel (See "Setting the default tray and paper" on page 27). •If you experience problems with paper feeding, check whether the paper meets the media specifications. Then, try placing one sheet at a time in tray (See "Print media specifications" on page 62, "Printing on special media" on page 30). •The settings made from the machine driver override the settings on the control panel. Manual feeding in the tray The tray can hold special sizes and types of print material, such as postcards, note cards, and envelopes. It is useful for single page printing on letterhead or colored paper. Tips on using the manual feeding method •If you select Paper > Source > Manual Feeder from your printer driver, you need to press each time you print a page. Load only one type, size and weight of print media at a time in the tray. •To prevent paper jams, do not add media while printing. •Print media should be loaded face up with the top edge going into the tray first and be placed in the center of the tray. •Always load the use recommended print media to avoid paper jams and print quality problems. (See "Print media specifications" on page 62.) •Flatten any curl on postcards, envelopes, and labels before loading them into the tray. 1.Load the paper in the tray. •When printing on special media, you must follow the loading guideline. (See "Printing on special media" on page 30.) •When paper does not feed well while printing, gently push the paper in manually until it starts feeding automatically. 2.Squeeze the tray paper width guides and adjust them to the width of the paper. Do not force them too much, or the paper will bend resulting in a paper jam or skew. 3.Open the output support. 4.To print from an application, open the application and open the print menu. 5.Open Printing Preferences. (See "Opening printing preferences" on page 34.) 6.Click on the Paper tab in Printing Preferences, and select an appropriate paper type. For example, if you want to use a label, set the paper type ...
Эта инструкция также подходит к моделям:Принтеры - ML-1860 (4.94 mb)
Принтеры - ML-1861 (4.94 mb)
Принтеры - ML-1861K (4.94 mb)
Принтеры - ML-1865 (4.94 mb)