Оценок - 3, средний балл: 4.3
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
When selecting envelopes, consider the following factors: -Weight: The weight of the envelope paper should not exceed 90 g/m2 or jamming may occur. -Construction: Prior to printing, envelopes should lie flat with less than 6 mm curl, and should not contain air. -Condition: Envelopes should not be wrinkled, nicked, or otherwise damaged. -Temperature: You should use envelopes that are compatible with the heat and pressure of the machine during operation. • Use only well-constructed envelopes with sharp and well creased folds. • Do not use stamped envelopes. • Do not use envelopes with clasps, snaps, windows, coated lining, self-adhesive seals, or other synthetic materials. • Do not use damaged or poorly made envelopes. • Be sure the seam at both ends of the envelope extends all the way to the corner of the envelope. 1 Acceptable 2 Unacceptable • Envelopes with a peel-off adhesive strip or with more than one flap that folds over to seal must use adhesives compatible with the machine’s fusing temperature for 0.1 second. Check your machine’s specification to view the fusing temperature, see page 40. The extra flaps and strips might cause wrinkling, creasing, or jams, and may even damage the fuser. • For the best print quality, position margins no closer than 15 mm from the edges of the envelope. • Avoid printing over the area where the envelope’s seams meet. MEDIA TYPE GUIDELINES Labels • To avoid damaging the machine, use only labels designed for use in laser machines. -When selecting labels, consider the following factors: -Adhesives: The adhesive material should be stable at your machine’s fusing temperature. Check your machine’s specification to view the fusing temperature, see page 40. -Arrangement: Only use labels with no exposed backing between them. Labels can peel off sheets that have spaces between the labels, causing serious jams. -Curl: Prior to printing, labels must lie flat with no more than 13 mm of curl in any direction. -Condition: Do not use labels with wrinkles, bubbles, or other indications of separation. • Make sure that there is no exposed adhesive material between labels. Exposed areas can cause labels to peel off during printing, which can cause paper jams. Exposed adhesive can also cause damage to machine components. • Do not run a sheet of labels through the machine more than once. The adhesive backing is designed for only a single pass through the machine. • Do not use labels that are separating from the backing sheet or are wrinkled, bubbled, or otherwise damaged. Card stock or custom-sized materials • Do not print on media smaller than 76 mm wide or 127 mm long. • In the software application, set margins at least 6.4 mm away from the edges of the material. Transparencies • To avoid damaging the machine, use only transparencies designed for use in laser printers. • Transparencies used in the machine must be able to withstand 180 °C, the machine’s fusing temperature. • Place them on a flat surface after removing them from the machine. • Do not leave them in the paper tray for long periods of time. Dust and dirt may accumulate on them, resulting in spotty printing. • To avoid smudging caused by fingerprints, handle them carefully. • To avoid fading, do not expose printed transparencies to prolonged sunlight. • Ensure that transparencies are not wrinkled, curled, or have any torn edges. • Do not use transparencies that separates from the backing sheet. • To prevent trancsparencies from sticking to each other, do not leave the printed sheets stack up as they are printed out. 20 _Selecting and loading print media Preprinted paper • Letterhead must be printed with heat-resistant ink that will not melt, vaporize, or release hazardous emissions when subjected to the machine’s fusing temperature for 0.1 second. Check your machine’s specification to view the fusing temperature, see page 40. • Letterhead ink must be non-flammable and should not adversely affect printer rollers. • Forms and letterhead should be sealed in a moisture-proof wrapping to prevent changes during storage. • Before you load preprinted paper, such as forms and letterhead, verify that the ink on the paper is dry. During the fusing process, wet ink can come off preprinted paper, reducing print quality. MEDIA TYPE GUIDELINES z Using photographic paper or coated paper may cause problems, requiring repairs. Such repairs are not covered by Samsung’s warranty or service agreements. LOADING PAPER Loading paper in the tray Load the print media you use for the majority of your print jobs in the tray. The tray can hold a maximum of 150 sheets of 75 g/m2 (20 lb bond) plain paper. 1. Grasp the paper input tray and pull it toward you to open. Pinch the rear guide and pull it out to extend the tray. Because the machine is very light, it may be moved when you use it; for example, when opening/closing the tray or installing/removing thetoner cartridge. Be careful not to move the machine. 2. Prepare a stack of paper for loading by flexing o...
Эта инструкция также подходит к моделям:Принтеры - ML-1640 (3.65 mb)
Принтеры - ML-1640K (3.65 mb)
Принтеры - ML-1641 (3.65 mb)
Принтеры - ML-1641K (3.65 mb)