|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
2 Adjust the contrast with “Lower” or “Higher”, and then select “OK”. Lower Each time it is selected, the contrast level decreases by 1 grade lower. (The distinction between brightness and darkness is reduced.) Higher Each time it is selected, the contrast level increases by 1 grade higher. (The distinction between brightness and darkness is increased.) ..The screen will return to step 1. Select “OK”, and then proceed to step 4 of Quality Adjusting (see page 28). ..To display this screen, refer to steps 1 and 2 of Quality Adjusting (see page 27). 30 Chapter 2 SD Print Settings Brightness Images can be printed with the adjusted brightness. Higher Lower 1 Select “Brightness”. 2 Adjust the brightness with “Lower” or “Higher”, and then select “OK”. ..To display this screen, refer to steps 1 and 2 of Quality Adjusting (see page 27). Lower Each time it is selected, the brightness level decreases by 1 grade lower. Higher Each time it is selected, the brightness level increases by 1 grade higher. ..The screen will return to step 1. Select “OK”, and then proceed to step 4 of Quality Adjusting (see page 28). Saturation Images can be printed with the adjusted saturation. 31 Chapter SD Lower Higher 1 Select “Saturation”. 2 Adjust the saturation with “Lower” or “Higher”, and then select “OK”. ..To display this screen, refer to steps 1 and 2 of Quality Adjusting (see page 27). Lower Each time it is selected, the saturation level decreases by 1 grade lower, reducing the color saturation. Higher Each time it is selected, the saturation level increases by 1 grade higher, increasing the color saturation. ..The screen will return to step 1. Select “OK”, and then proceed to step 4 of Quality Adjusting (see page 28). 32 Chapter 2 SD Print Settings Tint Images can be printed with reddish or bluish color accentuated. Reddish color accentuated Bluish color accentuated 1 Select “Tint”. 2 Adjust the color tone with “More Red” or “More Blue”, and then select “OK”. ..To display this screen, refer to steps 1 and 2 of Quality Adjusting (see page 27). More Red Each time it is selected, the level of reddish color increases by 1 grade. (The bluish color level decreases by 1 grade.) More Blue Each time it is selected, the level of bluish color increases by 1 grade. (The reddish color level decreases by 1 grade.) ..The screen will return to step 1. Select “OK”, and then proceed to step 4 of Quality Adjusting (see page 28). 33 Chapter SD 33 Chapter SD Color Balance Images can be printed with the adjusted density level (Darker, Medium, and Lighter) of Cyan, Magenta, Yellow, and Black. ..The density of each color can be fine tuned for each of the three density levels. ..This function is useful for the fine adjustment of color photos. Unlike image editing software, this function cannot greatly change the color tone since the adjustable range at each density level is very narrow. 1 Select “Color Balance”. 3 Select remaining colors, and then adjust the Color Balance as shown in step 2. 4 Select “OK”. ..To display this screen, refer to steps 1 and 2 of Quality Adjusting (see page 27). 2Select “Cyan”, and then adjust Darker Areas, Medium Areas, and Lighter Areas with “-” or “+”. ..The density range from the darkest level (100%) to the lightest level (0%) is equally divided into three range areas. ..The screen will return to step 1. Select “OK”, and then proceed to step 4 of Quality Adjusting (see page 28). Darker Areas Darkest area Medium Areas Area between the darkest and lightest areas Lighter Areas Lightest area 34 Chapter 2 SD Print Settings Sort Mode Printed copies can be sorted by set. The following Finishing modes are available instead of “Rotate-Sort” and “Rotate-Group” when the optional Finisher is installed. ..Only 8.5" x 11" (Letter/Letter-R) size is applicable for “Rotate-Sort” and “Rotate-Group”. When “Rotate-Sort” or “Rotate-Group” is selected with Letter and Letter-R size paper loaded in the paper tray, sets of copies are stacked in alternate direction (rotation of 90 degrees). ..The default setting of Sort can be changed with the Function Parameter “30 SD Print Settings (11 Sort Priority)” (Printer Settings > General User Mode). Refer to Printer Settings in the Operating Instructions (For Function Parameters) of provided CD-ROM. 1Select “More Settings”. 2Select “Sort Setting”. Ex: When “More Settings” is selected in “Thumbnail/Index Print” tab. 1114231Sort Rotate-Sort Rotate-Group Shift-Group Shift-Sort 1114231Sort Rotate-Sort Rotate-Group Shift-Group Shift-Sort ..To display “More Settings”, refer to steps 1 to 6 of Printing from SD Memory Card (see page 11) or steps 1 to 6 of Printing from USB Flash Memory (see page 14). 3 Select the desired sort setting, and then select “OK”. • When the optional Finisher is not installed • When the optional Finisher is installed 4 Select “Close”. ..For the following procedure, refer to steps 7 to 9 of Printing from SD Memory Card (see page 13) or steps 7 to 9 of Printing from USB Flash Memory (see ...