Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
WATER SUPPLY Suggested Min. Incoming Water Temperature 120°F to 150°F 49. to 66. Pressure (PSI) Minimum/Maximum 15/120 PSI Connection (NPT) 3/8” Consumption (Toil Gallons) 3.5±5% Water Valve Flow Rate (GPM) 1.08GPM±10% 3 Schenmatic Diamgram of Dishwasher (WQP8-9223 and WQP8-9324) AC110/120V 50/60Hz LGN IG 1 3 2 P1 IAQS RE 23 1 ISB ISS SMP20 1 11 ACN C1 IS T1 SMP16 1 9311513715 816 D- LED D1 D2 D3 D4 D12 D13 K1 D14D15 D5 K2 BUZ D6 D10 D11 D9 K3 D7 K4 VCC D8 C2 C3 ACN ACL 7805 contoller C4 code Cn EV1 capacitor inlet valvecomponentcode EV2D/ Ed softener valvecomponent dispenser IAQS flowt switch IG power switch IS door switchISBquicksilver switch ISSsalt switchITRthermic- hypersensitive switch LS D10 salt warning light power switchD9 ML rinse aid warning lightwashing pumpPSdrain pump Pwater level switch R1 heating elementRE thermic- hypersensitive resistanceS thermic- hypersensitive switch VCC RY1 RY2 TR1 TR2 TR3 TR4 TR5 TR6 TR7 TR8 TR9 TR10 MIC1 201019 918 817 7166 155 13 S S ITR(78) EV1 EV2 D/ Ed C R1 ML PS ITR(78) green R1 red green PSMLsoftener valve power switch washing pump rinse aid warning light water level switch thermic- hypersensitive switchquicksilver switch thermic- hypersensitive resistance white gray C EV1 gray EV2 D/ Ed PS P0drain pump thermic- hypersensitive switch heating element RE SR1 salt warning lightdoor switchflowt switch power switchsalt switch ISBD9 MLITRD/ Ed dispenser EV2 IG IS LS D10ISS capacitor inlet valveEV1 IAQS Cn Wiring Diagram of Dishwasher (WQP8-9223 and WQP8-9324) contoller 13ACLACND11 16 pink 155 RY1RY2 TR8 greenS 20 S 1720 TR2 TR9TR1 TR3 VCC D10D9 BUZ IAQS 32 P1 ISS ISB RE 5 13 8 167 15 black gray gray black pink white 1SMP16 119 3 red red white white 1 IS 32 1 D3 C2 C3 C4 component 18 6 white 9 TR10 TR6TR4 SMP20 yellow gray 17TR7 TR5 VCC K4K1 K3K2 7805 D7 D8D5 D6D4 D15 component codecode D14 C1T1 D- LED D1 D2 D13 ACN11 AC110/130V 50/60Hz D12 SMP20 1 IG NGL 5 TIMER CYCLE CHART COMPONENT OPERATION AND REPAIR SAFETY PRECATIONS Always turn off the electric power supply before servicing any electrical component, making ohmmeter checks, or replacing any parts. All voltage checks should be made with a voltmeter having a full scale range of 130 volts or higher. After service is completed, be sure all safety-grounding circuits are complete, all electrical connections are secure, and all access panels are in place. CIRCUIT BOARD With the circuit board, user selects the various cleaning cycles of the dishwasher with press the button. The circuit board controls all the electrical functions of the dishwasher in all stages of each cycle. All functions can be traced on the chart. Diagram provided in this service manual. To Test Circuit Board If the circuit board is suspected of faulty operation, reference chart and electrical schematic diagram and proceed as follows: 1. Index the circuit board to all of the increment of the cycle, each of the indicators light should is bright. 2. Index the circuit board to one of the increment of the cycle, which is a drain period. 3. If the pump motor fails to operate during the first cycle increment, check for power at the pump motor connector block, if there is no power check the door latch switch, if there is power, check the pump motor as described in this section. 4. If a component controlled by the circuit board fails to function as the circuit board advances through the cycle, check for voltage at the circuit board terminals. If the check voltage is supplied to the component, check the component as described in this section. Continuity through circuit board contacts, other controls, and wires can also be checked with an ohmmeter with electrical power disconnected. If the circuit boards contacts fail to close in the sequence shown on the ...
Эта инструкция также подходит к моделям:Посудомоечные машины - SB 818 (740.52 kb)
Посудомоечные машины - WB 818 (740.52 kb)
Посудомоечные машины - WB 818 (740.52 kb)