Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
Refill rinse aid. Select programme with drying (see Overview of programmes, Programme sequence). Arrange utensils in a sloping position, arrange affected utensils as sloping as possible. Use different combination detergent with better drying performance. Use of rinse aid also increases the drying performance. Activate intensive drying (see Operating the appliance) Wait until program ends or wait until 30 min after program ends before removing utensils. Use a proprietary rinse aid. Eco products are much less effective. Plastic utensils not dry. Special properties of plastic. Plastic has a lower heat storage capacity and therefore dries less well. Cutlery not dry. Cutlery not arranged properly in the cutlery basket. Cutlery not arranged properly in the cutlery drawer. Separate cutlery if possible, prevent contact points. Arrange cutlery properly and separate if possible. Appliance interior wet after rinse cycle. No appliance fault. On account of the “Condensation dr ying” principle, water droplets are physically induced and required in the container. The humidity in the air condenses on the inner walls of the dishwasher, drains and is pumped out. Food remnants on the utensils. Utensils placed too closely together, utensils basket overfilled. Spray arm rotation obstructed. Spray arm nozzles blocked. Filters 1j dirty. Filters 1j inserted incorrectly and/or not engaged. Rinse programme too weak. Arrange utensils with adequate clearance between them ensuring that the spray jets can reach the surface of the utensils. Prevent contact points. Arrange utensils so that the spray arm can rotate without obstruction. Clean the spray arm nozzles, (See Cleaning and maintenance). Clean filters, (see Cleaning and maintenance). Insert and engage filters correctly. Select a more intensive rinse programme. Utensils precleaned too intensely; sensors therefore decide on weak programme sequence. Stubborn soiling cannot be completely removed. Tall narrow receptacles in corner areas are not rinsed adequately. Do not prerinse utensils. Remove only large food remnants. Recommended programme Eco 50° or Intensive. Do not place hollow receptacles too obliquely and do not place in the corner area. Top basket 1* on right and left not Set top basket to same height using side set to same height. levers. 2 6 Fa ul t, w h at to do ? Fault Cause Remedial action Detergent residue Detergent dispenser cover blocked Detergent dispenser cover must not be by utensils and therefore does not obstructed by utensils. open fully. Do not place utensils or fragrance dispenser in the tablet collecting tray. Detergent dispenser cover blocked Tablet must be inserted flat and not upright. by the tablet. Tablets used in the quick or short pro-Dissolving time of tablets too long for a quick gramme. or short programme. Dissolving time of the detergent is not Use a detergent powder or select a more reached in the selected short pro-intensive programme. gramme. Washing effect and dissolving perform-Change detergent. ance are reduced after a prolonged storage time or detergent is very lumpy. Water stains on plastic parts Droplet formation on plastic surface is Use a more intensive programme (more water physically unavoidable. After drying, changes). water stains are visible. Arrange utensils in a sloping position. Use rinse aid. If required, increase softening setting. Washable or water-soluble coat-Detergent substances are deposited. Change detergent brand. ings in the container or on These coatings cannot usually be the door. removed with chemicals (appliance Clean appliance mechanically. cleaner, ...). If there is a “white coating” on Increase softening setting and change deter- the container floor, the water softening gent if required. system has been set marginally. Salt dispenser cover 1b not closed. Close salt dispenser cover correctly. Only for glasses: Initial glass corrosion See Glass and utensil damage. – can only apparently be wiped off. White, stubborn coatings; limes-Detergent substances are deposited. Change detergent brand. cale on the utensils, container or These coatings cannot usually be door. removed with chemicals (appliance Clean appliance mechanically. cleaner, ...). Hardness range incorrectly set or water Set water softening system according hardness greater than 8.9 mmol/l. to instructions for use or top up salt. 3 in 1 detergent or bio/eco detergent Set water softening system according not effective enough. to instructions for use or use separate detergents (proprietary detergent, salt, rinse aid). Underdosing of detergent. Increase detergent dosage or change detergent. Too weak rinse programme selected. Select a more intensive rinse programme. Tea or lipstick residue on Too low rinsing temperature. Select programme with higher washing tem- the utensils. perature. Too little or unsuitable detergent. Use suitable detergent at correct dosage. Utensils precleaned too intensely; sen-Do not prerinse utensils. Remove only large sors therefore deci...
Эта инструкция также подходит к моделям:Посудомоечные машины - DI461113/70 (2.15 mb)
Посудомоечные машины - DI461113/73 (2.15 mb)
Посудомоечные машины - DI461133/01 (2.15 mb)
Посудомоечные машины - DI461133/70 (2.15 mb)