Оценок - 2, средний балл: 4 ( )

Производитель: Kenmore Размер: 741.58 kb Название файла: Язык инструкции:

Refer to the "Cycles" section, page 12-13. Check to see if household fuse or circuit breaker is blown or tripped. Motor will automatically reset itself within a few minutes. If it does not restart, call for service. Checkto see if shut-off valve (if installed) is turned on. Check to see if the overfill protector moves up and down freely. Press down to release. It is normal for the dishwasher to run longer while heating water. Refer to the '_Nater temperature tips" section, page 11. oA delay will occur in the main wash if the Water Heat option is selected. • Three delays will occur if the Pots & Pans cycle is selected. • The final rinse will automatically delay until the water temperature reaches 135°F (57°C). Wait for the cycle to complete. Wait for the cycle to complete. Replace with dry, lump-free detergent. Refer to the "Parts and Features" section, page 3 and reinstall rack if necessary. Refer to the "Using the detergent dispenser" section, page 10. Try a different brand to reduce foaming and eliminate buildup. Run a Quick Rinse cycle at least once or twice a day until full load is accumulated. Run a vinegar rinse, as described on the next page. Dishwasher console should be aligned with countertop. Refer to Installation Instructions for more information. Refer to the "Loading Your Dishwasher" section, pages 7-9. Use the Water Heat option. If needed, turn home water heater up to ensure water entering dishwasher is 120°F (49°C) minimum. Refer to the "Water temperature tips" section, page 11. Use recommended dishwasher detergents only. Refer to the "Using the detergent dispenser" section, page 10. Never use less than one tablespoon per load. Detergent must be fresh to be effective. Always store detergent in a cool, dry area. Troubleshooting Guide (cont.) Dishes are not cleaned completely (cont.) PROBLEM ... CAUSE... Food soil left on Detergent cakes in dispenser dishes (cent.) Pump or spray arm clogged by labels from bottles and cans Insufficient fill caused by low water pressure Slowdown of wash arm due to high suds Spots or stains on dishes Spotting and filming Hard water or high mineral content in water Water temperature is too low Use of incorrect detergents Incorrect amount of detergent Use of ineffective detergents Insufficient fill caused by low water pressure Silica film or etching A water chemical reaction with (silica film is a milky, certain types of glassware. rainbow colored Usually caused by some deposit; etching is a combination of soft or softened cloudy film) water, alkaline washing solutions, insufficient rinsing, overloading the dishwasher, and heat of drying. SOLUTION... Use fresh detergent only. Do not allow detergent to sit for several hours in a wet dispenser. Check dispenser for caked detergent. Clean dispenser when caked detergent is present. Remove labels before washing bottles and cans or wash by hand. Refer to the "Tips for washing special items" section, page 17. Home water pressure should be 20 to 120 psi (138-828 kPa) for proper dishwasher fill. A booster pump on the water supply may be necessary if pressure is too low. Never use soap or laundry detergents. Use recommended dishwasher detergents only. Conditioning the final rinse water with a liquid rinse agent helps eliminate spotting and filming. Keep the dispenser full with a rinse agent at all times. Use the Water Heat option. If needed, turn home water heater up to ensure water entering dishwasher is 120°F (49°C) minimum. Refer to the "Water temperature tips" section page 11. Use recommended dishwasher detergents only. Refer to the =Using the detergent dispenser" section, page 10. Heavy soil and/or hard water generally require extra detergent. Detergent should be fresh. Store in a cocl, dry place, preferably in an airtight container. Discard lumpy detergent. Home water pressure should be 20 to 120 psi (138-828 kPa) for proper dishwasher fill. A booster pump on the water supply may be necessary if pressure is too low. NOTE: To remove spots and film from dishes, try a vinegar rinse. 1. Wash and rinse as usual using the No Heat Dry option. 2. Remove all metal items. 3. Put 2 cups (500 mL) white vinegar in a container on the bottom rack. 4. Run dishwasher through complete washing cycle. Vinegar will mix with wash water. It may not be possible to prevent problem, except by hand washing. To slow this process, use a minimum amount of detergent but not less than 1 tablespoon per load. Use a liquid rinse agent and underload the dishwasher to allow thorough rinsing. Silica film and etching are permanent and cannot be r...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: