Оценок - 3, средний балл: 4.3
(
)
)
|
Фото и характеристики Indesit DE 43 |
Фрагмент инструкции
Each time you press the button, a beep will sound and symbol corresponding to the upper rack or symbol corresponding to the lower rack will appear. If you press the button once more, the selection will be reset and the dishwasher will consequently wash on both racks. To use the racks correctly, we recommend you read the chapter entitled "Loading the dishes". Cycle phase under way indicator Your dishwasher is equipped with an indicator "G" comprising 4 symbols which represent the different phases of a wash cycle. When the wash cycle has started, the display will indicate the phases under way in sequence. These phases are: pre-wash wash rinses drying Cancelling and modifying a wash cycle in progress Premise: a wash cycle in progress can only be modified if it hasn't been running for long. To modify it, turn the knob and set it to RESET. After a few seconds, you will hear 4 beeps, indicator "G" relating to the phase under way will turn off and 3 dashes will appear. At this point, all the settings will have been cancelled. To select a new wash cycle, repeat the instructions contained in the paragraph entitled "Starting and setting the cycle". You've left out a dish? You can interrupt a wash cycle by pressing the "ON-OFF" button, then place the forgotten dishes into the appliance, which will start up from where it was interrupted when you turn it back on. There's been a power failure? Have you opened the dishwasher door? The wash cycle stops and then restarts when the electricity comes back on or when you shut the door. How to programme extra drying. If you want your dishes to be perfectly dry, follow the instructions below. Set the knob to RESET and make any specific settings, such as: -upper or lower rack -delayed start Start the wash cycle by turning the knob and open the appliance door. Observe symbol for drying: it will flash for about 4 seconds, while the word "OFF" appears on the display (extra drying disabled). If you press button "I" immediately, you will hear a prolonged beep and the word "ON" will appear on the display: the extra drying has been enabled. Once you have made your selection, shut the appliance door; a beep will sound and the wash cycle will either start immediately or after the delay, wherever set. Remember that with extra drying, the wash cycle will last longer, to provide you with drier dishes. At the end of the wash cycle At the end of the wash cycle, 2 beeps are sounded and the word END flashes. Bring the selector back to the RESET position, and the 3 dashes for programming cancellation will appear. Turn the appliance off by pressing the ON-OFF button, turn off the water tap and open the door. Wait a few minutes before removing the dishes: this way you won't have to handle them while they're still hot and they will dry better. Empty the bottom rack first. Make sure the wash cycle has ended before removing the dishes! Warning If opening the door soon after the end of the programme,or during it, stand away from the Dishwasher, to avoid possible injury from hot steam. GB 6 Setting a delayed start on a wash cycle When you have loaded the dishes, you can choose when to start your dishwasher before setting the wash cycle desired. l• Press button "D" and you can delay the start of the wash cycle by 1 to 9 hours. Press the button once, a beep will sound and the wording "09 h" will come up on the display. Then, each time you press the button a beep will sound and the hours will decrease by one hour until the delay is 01 h. If you press the button once again, the delayed start is reset and 3 dashes appear on the display. Note: the delayed start is also reset automatically should you fail to select the wash cycle on knob "M" within 15 seconds. l Once you have set the delayed start time, select the wash cycle on the knob: after the beep sounds, you will see indicator light "H" flash on the display and the countdown begins (indicated on the display one hour at a time). A quick look at the indicator lights will keep you informed of the countdown progress at all times. Have you changed your mind? w• During the countdown, you can modify the delay by pressing button "D" repeatedly without resetting the wash cycle. w• If you have changed your mind and wish to start the wash cycle immediately, press button "D" until the countdown is fully reset. Indicator light "H" will turn off and the cycle will start at the sound of a beep. The indicator light corresponding to the cycle phase under way will come up on the display and the countdown to the estimated cycle end begins. 7 GB Wash Cycle Table Cycle Cycle selection instructions Cycle description Detergent for prewash + wash Rinse Aid 1) Intensive Very dirty dishes and pans (not to be used for delicate items). Pre-wash with cold water Pre-wash with hot water at 45°C Extended wash at 70°C. Cold rinse Rinse with hot water at 70°C. Drying. 5+15 gr. * 2) Normal Normally dirty pans and dishes. Standard daily cycle. 2 pre-washes with cold water. Extended wash at ...