Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
If the appliance settings have to be changed, follow the instructions in the section "Gas connection and conversion to a different gas type". ¦ This appliance is not connected to a waste gas main. It must be connected and commissioned in accordance with the installation conditions. Do not connect the appliance to a waste gas main. All ventilation regulations must be observed. ¦ The gas connection must be made via a fixed, i.e. not mobile connection (gas line) or via a safety hose. ¦ If using the safety hose, ensure that the hose is not trapped or crushed. The hose must not come into contact with hot surfaces. ¦ The gas line (gas pipe or safety hose) can be connected to the right or left-hand side of the appliance. The connection must have an easily accessible locking device. Faults in the gas installation/smell of gas If you notice a smell of gas or faults in the gas installation, you must ¦ immediately shut off the gas supply and/or close the gas cylinder valve ¦ immediately extinguish all naked flames and cigarettes ¦ switch off electrical appliances and lights ¦ open windows and ventilate the room ¦ call the aftersales service or the gas supplier Moving the appliance by the gas line or door handle Do not move the appliance while holding the gas line; the gas pipe could be damaged. There is a risk of a gas leak! Do not move the appliance while holding it by the door handle. The door hinges and door handle could be damaged. Electrical connection Caution! ¦ Have the appliance set up by your after-sales service. A 16 A fuse is required for connection. The appliance is designed for operation at 220-240 V. ¦ If the electricity supply drops below 180 V, the electrical ignition system does not work. ¦ Any damage arising from the appliance being connected incorrectly will invalidate the guarantee. ¦ If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. For the after-sales service Caution! ¦ The appliance must be connected in accordance with the data on the rating plate. ¦ Only connect the appliance to an electrical connection that meets the applicable provisions. The socket must be easily accessible so that you can disconnect the appliance from the electricity supply if necessary. ¦ Please ensure the availability of a multi-pin disconnecting system. ¦ Never use extension cables or multiple plugs. ¦ For safety reasons, this appliance must only be connected to an earthed connection. If the safety earth terminal does not comply with regulations, safety against electrical hazards is not guaranteed. ¦ You must use a H 05 W-F type cable or equivalent for the appliance connection. Horizontal alignment Always set up the appliance directly on the kitchen floor. The appliance is equipped with adjustable feet to set the height. You can raise the appliance approximately 15 mm by adjusting the feet. The adjustable feet are located at the front and rear corners underneath the oven. You can adjust the feet, using a spanner, to ensure that the appliance is horizontal. Wall fixing To prevent the cooker from tipping over, you must fix it to the wall using the enclosed bracket. Please observe the installation instructions for fixing the oven to the wall. Setting up the appliance ¦ The appliance must be set up directly on the kitchen floor and in line with the specified dimensions. The appliance must not be set up on any other object. ¦ The distance between the top edge of the oven and the bottom edge of the extractor hood must meet the requirements of the extractor hood manufacturer. ¦ Ensure that the appliance is not moved again after set up. The distance from the high output burner or wok burner to the fronts of the adjacent units or the wall must be at least 50 mm. Measures to be noted during transport Secure all mobile parts in and on the appliance using an adhesive tape that can be removed without leaving any traces. Push all accessories (e.g. baking tray) into the corresponding slots with cardboard at the edges, in order to avoid damaging the appliance. Place cardboard or similar between the front and rear side to prevent knocks against the inside of the glass door. Secure the door and, if available, the top cover to the appliance sides using adhesive tape. Keep the original appliance packaging. Only transport the appliance in the original packaging. Observe the transport arrows on the packaging. If the original packaging is no longer available pack the appliance in protective packaging to guarantee sufficient protection against any transport damage. Transport the appliance in an upright position. Do not hold the appliance by the door handle or the connections on the rear, as these could be damaged. Do not place any heavy objects on the appliance. Your new cooker Here you will learn about your new cooker. We will explain the control panel, the hob and the individual operating controls. General information The design depends on the...