Войти:
Оценок - 3, средний балл: 4.3 ( )

Инструкция по эксплуатации Empire Comfort Systems, модель ES-S100

Производитель: Empire Comfort Systems
Размер: 218.49 kb
Название файла:
Язык инструкции:enfr
Перейти к скачиванию



Фрагмент инструкции


Apply nuts and tighten securely. Now tighten leg bolts. 2. Install manifold clamps. Insert two long bolts through manifold clamp holes in the main top. Attach the two manifold clamps loosely (10,000 Btu per Burner) underneath top, using nuts. Place manifold pipe with valves attached into the clamps. Align the gas valves with center of large opening in top. The adjusting hood of the valve should face the rear of the stove. Now tighten the manifold clamps securely. Place the valve knobs on valve stem, making sure that the control valve is in the off position. Knob should be in the vertical position. Manifold Pipe thread is 3/8 male IPS. 3. To install burners: If stove is to be used with LP or bottled gas, the air shutter (round metal disc) should be partially opened and then locked in place by tightening the air shutter screw. The hole in open end of burner slides over the adjusting hood of the gas valve. The rear part of the burner is attached to hole underneath main top using long bolts with nuts. Fasten securely. 4. The grates are installed by inserting the two extended legs on grate into corresponding holes in main top on each side of burner opening. 5. Always use teflon tape or thread sealer on pipe threads. FOR MINI-STOVE MODELS (NUMBER MS-100, MS-200, MS300)) 6. Remove the main top by pulling upward. Install the two manifold clamps, using the long bolts with nuts, to the bottom front of frame. Do not tighten clamps. 7. Insert the manifold pipe with valves attached into the clamps; open end of manifold should extend through hole in left side of frame. Tighten the manifold clamps. Burners are fastened to burner hangers already installed. Then assemble in same manner as above. CHECK FOR GAS LEAKS After assembly is complete, connect stove to gas supply and check for gas leaks before lighting. Make sure proper fittings are used for connection. (To operate gas valve, push in before turning.) 1. Turn brass control valve so knob is in vertical position until it is tight. (This shuts off flow of gas from the regulator to the burner. 2. Open LP cylinder valve or gas supply by 1/4 turn. This allows gas into the regulator and stops it at the brass control valve. 3. Apply gas detector fluid (or soapy dishwashing solution) on all connections, especially around the regulator, valve and POL-cylinder GRATE BURNER TOP 1/4" BOLT 1/4" HEX FLANGE NUT BODY LEG Model No. SE-200 w/SLK-28 VALVE KNOB connection. Any bub-bles that appear indicate a gas leak. If so, turn off gas and tighten the fitting. If a leak persists, pipe thread compound may be needed on the threads. NEVER USE A FLAME TO CHECK FOR GAS LEAKS. Cylinder Service Valve TO LIGHT 1. When you are sure there are no gas leaks, WRENCH TIGHTENED ASSEMBLY Regulator POL Connector Handwheel Pressure Relief Valve turn cylinder valve and brass control valve to closed position. (To operate gas valve, push in before turning.) 2. Re-open LP cylinder valve fully. 3. Re-open brass control valve 1/4 turn. 4. Keeping ha...

Эта инструкция также подходит к моделям:
Плиты - ES-S200ES-S200 (218.49 kb)
Плиты - ES-200 (218.49 kb)
Плиты - ES-100 (218.49 kb)
Плиты - ES-300 (218.49 kb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории