Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Windows and doors in the home should be opened to help ventilate as these oils burn off. NOTE: If the unit does not start, DO NOT try to restart the unit until it has cooled completely down. If the unit does not start or maintain a fire, you will receive an E-2 in the Heat Range and Blower Speed window of the Control Board. If this occurs, wait until unit has cooled completely down and repeat these steps. FUEL NOT FEEDING CORRECTLY If the fuel is not feeding correctly, the feed auger could possibly be misaligned due to factors such as rough handling during shipping. If you suspect your feed auger is misaligned, call Customer Service at (800) 245-6489. CORN START-UP PROCEDURE When starting the stove with corn, push the “AIR ON TEMP” button and hold, which will rotate the stirrer mechanism in the burn pot. Release the button when the stirrer is strait up (in the “12:00” position) before following the above instructions concerning placing the handful of pellets in the fire pot and starting your fire. Changing from Corn to Pellets Your unit was primarily designed to burn corn, but will also burn hardwood pellets. Your unit comes ready to burn corn by default; if you wood like to burn pellets in your unit, follow the steps below. WARNING: Do not open the door on this unit if the stirrer is still moving! See instructions on “Setting the Stirrer” earlier in this manual. NOTE: Before doing these steps make sure the unit is out and completely cold!! 1. Remove the stirrer shaft (See Illustration 2) 2. Unplug the unit and plug back in, then press the Heat Range down and Blower Speed down buttons at the same time and release. You should see a “P” in the Heat Range window. 3. Follow lighting instructions. PELLET START-UP PROCEDURE NOTE: When burning only pellets, remove stirrer from fire pot. See Illustration 2. While you will not follow the instructions in the above “Corn Start-Up Procedure,” you will follow the instructions on “Changing from Corn to Pellets” and the other “Start-Up Procedures” in the preceding “Operating Instructions” section of this manual. If the unit does not start or maintain a fire, you will receive an E-2 in the Heat Range and Blower Speed window of the Control Board. If this occurs, wait until unit has cooled completely down and repeat. To remove the stirrer for burning pellets While the unit is COLD and the unit is off, press and hold the Air On Temp button until the stirrer is at the “12:00” position; loosen the Allen head Set Screw (marked in Illustration 2). Slide the locking collar (also marked in Illustration 2) to the fire pot. Lifting the fire pot and stirrer at the same time, remove the stirrer from the fire pot and replace fire pot back into the unit. NOTE: When replacing the fire pot, notice there is a welded piece that is always set toward the back of the fire box. Text Box: Text Box: Locking Collar Text Box: Set Screw Text Box: Illustration 2 E-Codes “E-Codes,” or Error Codes, are codes that will appear in the Heat Range and Blower Speed windows of the Control Board if your unit experiences problems. If you receive these codes, wait until the unit is cooled completely down before trying to restart your unit. If the unit continues to display any E-Code(s), please contact Customer Service at (800) 245-6489 before further attempting to restart your unit. E-2 = Fail to Start NOTE: “E-0” indicates “No Error” First Fire: When you push the “ON” button, the Control Board will automatically be set at both “Heat Range” and “Blower Speed” to setting “5”. Allow the stove to burn in this manner for at least three (3) hours. This will allow the unit to “cure out” as the paint and the oils from the manufacturing process burn off. We recommend you open doors and windows in your dwelling during this process. Subsequent Cold Starts: In a cold start situation, the unit should be operated at a “5” setting until the room air blower begins to operate. NOTE: Press the “ON” button only once on start-up. Pressing the “ON” button a second time during the start-up cycle will cause the start-up cycle to begin again. IMPORTANT: If the unit fails to start properly, or does not properly complete the Shut-Down procedure, open the closest outside door and a window to eliminate the home’s natural draft BEFORE opening the stove’s door or hopper lid. This will allow any smoke to exit through the external air hook-up instead of spilling into the home. SHUT-DOWN PROCEDURE WARNING: NEVER SHUT DOWN THIS UNIT BY UNPLUGGING IT FROM THE POWER SOURCE. Refer to the following instructions: Press the “OFF” touch pad to put the stove in the “Shut-Down” mode. There will be an “S D” in the Heat Range and Blower Speed windows while the unit is shutting down to verify this. At this time the red light above the “OFF” pad will illuminate. When the “OFF” pad is touched the auger will instantly stop feeding fuel to the auger tube, but the room air blower, exhaust blower and bottom auger will continue to operate. When the internal temper...
Эта инструкция также подходит к моделям:Плиты - 49-SHC22 (1.28 mb)
Плиты - 49-TRC22 (1.28 mb)