Оценок - 3, средний балл: 4.7
(
)
)
|
Фрагмент инструкции
Never connect the digital output socket to a conventional audio input. AUDIO OUTPUTS Connect to your amplifier’s CD orAUX inputs using suitable high quality interconnect cables. Insert the phono plug which is red [or marked ‘R’, or with a red ring] into the socket labelled 'R' and the other plug into the socket labelled 'L'. ALPHA 8, 8SE & 9 ONLYThe second set of sockets can be used to connect to a second amplifier set up for multi room use. Note Interconnecting cables are not supplied with this CD Player We recommend high quality cables as inferior quality cables will degrade the sound quality of your system. Please contact your Arcam dealer or Arcam customer support for details of suitable cables. Using your CD player - getting started POWER Press this button to switch the CD player on and off When first powered up with no CD installed you will see... ...first this ...then this LOAD (called OPEN on remote control) To install a CD, press ‘LOAD'. The CD tray opens, it accepts both 8 cm and 12 cm discs. Place the CD in the tray with the label side uppermost. Press 'LOAD' again [or press ‘PLAY', or gently push the tray in 5mm], the tray closes. You will see 'DISC', along with the total number of tracks and total disc time, eg. If the disc has rrfore than 16 tracks then the word 'OVER' is also shown on the display. The display returns to '0' after a few seconds. It is now ready to play. PLAY ► Press to play the CD. To restart the disc from track I, press ‘STOP’ and then ‘PLAY’. Note: Make sure your amplifier (input source selector) is set to CD. HDCD encoded CDs will be recognised automatically by the Alpha 8SE and 9CD players.To indicate this, a red LED (Light Emitting Diode) will illuminate behind the Arcam badge in the top left hand corner of the front panel whenever an HDCD disc is playing. STOP ■ Press to stop the CD playing. The display will show an '0' and the number of tracks. PAUSE ■■ Press to pause the disc (interrupt play). Press 'PAUSE' again to resume play from the same point. SEARCH -m ►► Press ■+* to search back or ►►to search foiward, for a particular passage during play. If the player is in 'PAUSE' mode the search will be at high speed and the sound will be muted (you will hear nothing). TRACK - PREVIOUS or NEXT H H To start the CD with a track other than the first one, press H or y* to locate your desired track, then press 'PLAvY', To select another track during play, press H or H to locate the track. The player will automatically 'PLAY' after you have selected the track. Pressing H once will restart the track currently playing. To select the previous track, press H twice. To go back two tracks, press three times, and so on. Using your CD player - getting started contmued HtoackH -power DISPLAY Dims or turns the display off and on. Turning the display off will generally give a slight improvement in sound quality. Pressing 'DISPLAY' once turns the display off To dim the display press the 'DISPLAY' button twice. To restore the display to full brightness press ‘DISPLAY’ a third time. REPEAT To repeat the entire CD or a pre-programmed selection of tracks press 'REPEAT' once. 'REPEAT' will illuminate on the display. To repeat one particular track go to the track you wish to repeat by using the H or H buttons (or the 0-9 keypad on the remote control) and press 'PLAY'. Then press the REPEAT button twice so that 'REPEAT I ’ is illuminated on the display. If you now select a different track, that one will be repeated instead. To cancel the repeat function press 'REPEAT' a third time. PROG To programme a selection of up to 24 tracks from a disc in any order To program your choice of tracks press Track H or H , or use the remote’s 0-9 keypad orTrack and H buttons, to locate the desired track. Press ‘PROG' to program the track into memory (RMS is illuminated on the display to indicate that you have begun a programmed sequence). Repeat these steps to program all the desired tracks into the player The display will show the track numbers that have been programmed, the total length of the programmed sequence and how many tracks have been programmed by use of the number above the word 'STEP'. If you press H or H or use the 0-9 keypad to direct dial to a track the number above the 'STEP' will change by one and start to flash until you press 'PROG'. After pressing 'PROG' the number will stop flashing. If you fail to press 'PROG' within about 5 seconds the display will also stop flashing and you will have to reselect the track you want to program. Press 'PLAY' to start playback of the programmed tracks. The existing program may be replayed by pressing'PLAY'. To clear the programmed sequence of tracks press STOP twice. CHECK To confirm your programmed sequence, press‘CHECK’. The first programmed track number and track time will be displayed. Subsequent pressing of the 'CHECK' button will display the next track details and total time of the sequence so far After check...
Эта инструкция также подходит к моделям:Плееры - 7 (840.8 kb)
Плееры - 8SE (840.8 kb)
Плееры - 9 (840.8 kb)