Оценок - 2, средний балл: 4.5
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
The player changes to speed-setting mode. Select the speed while listening the sound. 4 Slide the jog lever repeatedly to select the desired playback speed, and then press the jog lever to enter the selection. “DPC” appears in the display. To cancel the procedure Press x for 2 seconds or more. To return to the preceding setting Press x. z Once you open the lid, the playback speed reverts to the normal speed (0%). Note When using digital pitch control, you may hear noise or an echo in the playback. For the recorder operation, see page 63. Setting the alarm (Melody Timer) The alarm is convenient way to remind yourself of important times, such as when to get off the train. The alarm can be set to go off in 1 to 99 minutes. The alarm will also go off while the recorder is stopped. DISPLAY Jog lever (., >, ENT) 1 Press DISPLAY for 2 seconds or more. 2 Slide the jog lever repeatedly until “USEFUL” appears in the display, and then press the jog lever. 3 Slide the jog lever repeatedly until “M-TIMER” appears in the display, and then press the jog lever. 4 Slide the jog lever repeatedly until “ON” appears in the display, and then press the jog lever. , appears. 5 Slide the jog lever repeatedly to select the alarm sound, and then press the jog lever. You can select from three kinds of sounds. Display Alarm sound TIMER 1 Classical music 1 TIMER 2 Classical music 2 TIMER 3 Classical music 3 6 Slide the jog lever repeatedly to select the elapsed time. Each time you slide the jog lever, the elapsed time setting (TIME :) changes by 1 minute, within a range of 1 to 99 minutes. 7 Press the jog lever to enter the setting. The time remaining until the alarm is shown in the display while the recorder is stopped. To cancel the procedure Press x for 2 seconds or more. To return to the preceding setting Press x. To check the time remaining until the alarm Stop playback. The remaining time will appear in the display after a short while. Do steps 1 to 6 again to display the remaining time during play or play-pause. To cancel the alarm setting Select “OFF” in step 4. To stop the alarm Press any button. z • If you end the procedure after step 4, the previous alarm setting is automatically used. • After sounding for one minute, the alarm will automatically stop and the alarm setting will be canceled. If the alarm sounds during stop mode, then the power will automatically turn off 10 seconds after the alarm stops. If the alarm stops while an MD is playing, the playback will continue uninterrupted. Notes • The settings will be lost when you start recording. • The timer will begin counting down from the moment you select “ON” in step 4. The recorder will begin counting down again from the moment you change the elapsed time in step 6. For the recorder operation, see page 68. Connecting to a stereo system (LINE OUT) You can listen to the playback sound from connected component. Connect the i/ LINE OUT jack of the recorder to the LINE IN jacks of an amplifier or a tape player with a line cable. To LINE IN 2 phono plugs Stereo mini-plug R (red) Line cable To i/LINE OUT Jog dial Stereo system, etc. L (white) 4 Turn the jog dial until “LINE OUT” appears in the display, and then press the jog dial to enter the selection. Notes • If the “AUDIO OUT” parameter for the i/ LINE OUT jack is set to “LINE OUT”, VOL + or –, Virtual Surround, or 6-Band Equalizer will not function. • The “AUDIO OUT” parameter for the i/ LINE OUT jack cannot be set to “LINE OUT” when the remote control is connected. • When you connect the headphones/earphones directly to the recorder, set the “AUDIO OUT” parameter for the i/LINE OUT jack to “HeadPhone” in step 4. When connecting a line cable to the i/ LINE OUT jack of the recorder, be sure to set the “AUDIO OUT” parameter for the i/LINE OUT jack. 1 Press the jog dial. 2 Turn the jog dial until “USEFUL” appears in the display, and then press the jog dial. 3 Turn the dial until “AUDIO OUT” appears in the display, and then press the jog dial. Editing recorded tracks This section explains the operations that are done on the recorder. For details on operations done on the remote control, see the pages indicated for each operation. Before editing You can edit your recordings by adding/ erasing track marks or labeling tracks and MDs. Notes • Premastered MDs cannot be edited. • Close the record-protect tab on the side of the MD before editing • When “TOC Edit” is flashing, the editing results are being recorded. —Do not move or jog the recorder. —Do not disconnect the power source. —The lid becomes locked. Labeling a track or a disc (Name) You can name tracks and discs using the recorder’s character palette. Note To label a group, see page 50. Available characters • Capital and small letters of the English alphabet • Numbers 0 to 9 • ! " # $ % & ( ) *. ; < = > ? @_ ` +–' ,/: _ (space) Maximum number of characters per name Track names, group names, and disc name: Approx. 200 each (containing a mixture of all available characters) M...