Оценок - 3, средний балл: 4.7
(
)
)
|
Фрагмент инструкции
. • To reduce the risk of damage to charger body and cord, pull by charger plug rather than cord when disconnecting charger. • An extension cord should not be used unless absolutely necessary. Use of improper extension cord could result in a risk of fire and electric shock. If extension cord must be used, make sure: a. That pins on plug of extension cord are the same number, size and shape as those of plug on charger. b. That extension cord is properly wired and in good electrical condition; and c. That wire size is large enough for AC ampere rating of charger as specified below: Cord Length (Feet) 25' 50' 100' Cord Size(AWG) 16 16 16 Note: AWG = American Wire Gage DO NOT OPERATE CHARGER WITH A DAMAGED CORD OR PLUG. If damaged, have replaced immediately by a qualified serviceman. Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in any way; take it to a qualified serviceman. Do not disassemble charger; take it to a qualified serviceman when service or repair is required. Incorrect reassembly may result in a risk of electric shock or fire. To reduce the risk of electric shock, unplug charger from outlet before attempting any maintenance or cleaning. Turning off controls will not reduce this risk. • Do not use charger in wet or damp conditions. • Disconnect charger from power supply when not in use. • SAVE THESE INSTRUCTIONS. Review them frequently and use them to instruct others who may use this light. If you loan someone this light, loan them these instructions also. SAVE THESE INSTRUCTIONS BATTERY PACK/CHARGER The battery pack and charger are not included with your worklight. They are both sold separately. When purchasing, use the following information: MODEL NO, BATTERY PACK CHARGER 973,113900 Item No. 9_11378 Item No. 9_11379 (1323509) (1426101 ) BATTERY PACK The battery pack for your worklight has been shipped in a low charge condition to prevent possible problems. Therefore, you should charge it overnight prior tO use. Note: Batteries will not reach full charge the first time they are charged. Allow several cycles (operating worklight followed by recharging) for batteries to become fully charged. CHARGING BATTERY PACK See Figure 1. • Charge battery pack only with the recommended charger. • Make sure power supply is normal household voltage, 120 volts, 60 Hz, AC only. • Connect charger to power supply. • Place battery pack in charging stand. Align raised rib on battery pack with groove in charging stand. See Figure 1. • Press down on battery pack to be sure contacts on battery pack engage properly with contacts in charging stand. • The charge indicator light (LED), located on the charging stand, will light up red and glow when the charger is properly connected to power supply. This light indicates the charger is operating properly. It will remain on until battery pack is BATTERYPACKSHOWN IN CHARGINGSTAND removed from charging stand or charger is disconnected from power supply. • Note: If charger does not charge battery pack, return battery pack and charger to your nearest Sears Repair Center for electrical check. • After normal usage, 3 hours or less of charging time is required to fully recharge battery pack. Note: If battery pack is completely discharged, 6 hours or longer of charging time is required to fully recharge battery pack. • The battery pack will become slightly warm to the touch while charging. This is normal and does not indicate a problem. • Do not place charger in an area of extreme heat or cold. It will work best at normal room temperature. • When batteries become fully charged, unplug charger from power supply and remove the battery pack. IMPORTANT INFORMATION FOR RECHARGING HOT BATTERIES When using your worklight continuously, the batteries in your battery pack will become hot. You should let a hot battery pack cool down for approximately 30 minutes before attempting to recharge. Note: This situation only occurs when continuous use of your worklight causes the batteries to become hot. It does not occur under normal circumstances. Refer to "CHARGING BATTERY PACK" for normal re charging of batteries. If the charger does not charge your battery pack under normal circumstances, return both the battery pack and charger to your nearest Sears Repair Center for electrical check. CHARGER REDLIGHT (LED) CHARGINGSTAND Fig. 1 TO INSTALL/REMOVE BATTERY PACK See Figure 2. • Use only the recommended battery pack with your worklight. _, WARNING: Do not install battery pack to your u worklight until you have read and understood all precautions and operating instructions in the manual and printed on battery pack and charger. Orient battery pack so that raised rib on battery pack aligns with groove inside worklight. Battery pack is designed to fit only one way in worklight handle. • Insert battery pack, making sure latches on each side of battery pack snap into place and battery pack is secure in worklight before use. _k AUTION: When placing battery pack in your ...
Эта инструкция также подходит к моделям:Осветительные приборы - 973.113900 (378.6 kb)