Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
9_11378 Item No. 9_11379 (1323509) (1426101 ) BATTERY PACK The battery pack for your worklight has been shipped in a low charge condition to prevent possible problems. Therefore, you should charge it overnight prior tO use. Note: Batteries will not reach full charge the first time they are charged. Allow several cycles (operating worklight followed by recharging) for batteries to become fully charged. CHARGING BATTERY PACK See Figure 1. • Charge battery pack only with the recommended charger. • Make sure power supply is normal household voltage, 120 volts, 60 Hz, AC only. • Connect charger to power supply. • Place battery pack in charging stand. Align raised rib on battery pack with groove in charging stand. See Figure 1. • Press down on battery pack to be sure contacts on battery pack engage properly with contacts in charging stand. • The charge indicator light (LED), located on the charging stand, will light up red and glow when the charger is properly connected to power supply. This light indicates the charger is operating properly. It will remain on until battery pack is BATTERYPACKSHOWN IN CHARGINGSTAND removed from charging stand or charger is disconnected from power supply. • Note: If charger does not charge battery pack, return battery pack and charger to your nearest Sears Repair Center for electrical check. • After normal usage, 3 hours or less of charging time is required to fully recharge battery pack. Note: If battery pack is completely discharged, 6 hours or longer of charging time is required to fully recharge battery pack. • The battery pack will become slightly warm to the touch while charging. This is normal and does not indicate a problem. • Do not place charger in an area of extreme heat or cold. It will work best at normal room temperature. • When batteries become fully charged, unplug charger from power supply and remove the battery pack. IMPORTANT INFORMATION FOR RECHARGING HOT BATTERIES When using your worklight continuously, the batteries in your battery pack will become hot. You should let a hot battery pack cool down for approximately 30 minutes before attempting to recharge. Note: This situation only occurs when continuous use of your worklight causes the batteries to become hot. It does not occur under normal circumstances. Refer to "CHARGING BATTERY PACK" for normal re charging of batteries. If the charger does not charge your battery pack under normal circumstances, return both the battery pack and charger to your nearest Sears Repair Center for electrical check. CHARGER REDLIGHT (LED) CHARGINGSTAND Fig. 1 TO INSTALL/REMOVE BATTERY PACK See Figure 2. • Use only the recommended battery pack with your worklight. _, WARNING: Do not install battery pack to your u worklight until you have read and understood all precautions and operating instructions in the manual and printed on battery pack and charger. Orient battery pack so that raised rib on battery pack aligns with groove inside worklight. Battery pack is designed to fit only one way in worklight handle. • Insert battery pack, making sure latches on each side of battery pack snap into place and battery pack is secure in worklight before use. _k AUTION: When placing battery pack in your worklight, be sure raised rib on battery pack aligns with groove inside worklight handle and latches snap into place properly. Improper assembly of battery pack can cause damage to internal components. • To remove battery pack, locate latches on end of battery pack and depress to release battery pack from your worklight. SWITCH See Figure 3. To turn your worklight on and off, depress switch trigger. MULTI-POSITION HEAD See Figure 3. Your worklight has the feature of a multi-position head. Rotate head to the desired position as shown in the arrows in Figure 3. MULTI-POSITION HEAD SWITCH TRIGGER Fig. 3 BATTERY PACK LATCHES DEPRESSLATCHESTO RELEASEBATTERYPACK Fig. 2 Do not abuse power tools. Abusive practices can _k ARNING: When servicing, use only identical Craftsman replacement parts. Use of damage tool as well as workpiece. any other part may create a hazard or cause product damage. ,_ WARNING: Do not at any time let brake fluids, gasoline, petroleum-based products, penetrating oils, etc. come in contact with plastic parts. They contain chemicals that can damage, weaken or destroy plastic. BULB REPLACEMENT See Figure 4. When purchasing replacement bulb, request recommended part number 981258-001. See Figure 4. TO REPLACE BULB: • Remove battery pack from worklight. See Page 5. • Depress button located on top of len cover then pull lens cover to remove. • Remove old bulb from spring by twisting bulb in a clockwise direction. LENSCOVER PULLLENS COVERFORWARD TO REMOVE _k ARNING: Do not attempt to modify this worklight or create accessories not recommended for use with this worklight. Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious personal injury. • Insert new bulb in spring by twis...
Эта инструкция также подходит к моделям:Осветительные приборы - 11390 (378.6 kb)