Оценок - 5, средний балл: 4.2
(
)
)
|
Фрагмент инструкции
To turn the appliance completely off, remove the plug from the outlet. Room temperature button Press this button to display the Temperature on the LCD display. If you press the button once the display will show the °F . If you press the button twice, the display will show the temperature in °C. After few seconds, the display will automatically show the humidity level. FAN speed button Press this button to select the Fan Speed (High, Medium, Low). Decrease or increase Humidity Level/ Time buttons These buttons are used to adjust the desired humidity level, with 5% increments; they are also used to set the timer. From 0 -10 the hours increase by 30 min. and from 10-24 the hours increase by 1 hour increments. TIMER button With the appliance switched ON, if you press the TIMER button the display will show the hours after which you want the appliance to switch OFF (1-2-3... hours ). With the appliance in the STAND-BY position, if you press the TIMER button the display will show the hours after which you want the appliance to switch ON (1-2-3... hours ). MODE button Press this button to select the Fan only or Dehumidifier modes. TURBO POWER button Use this button to activate the “turbo power” function. In this mode, the appliance will operate at maximum fan speed and in continuous mode. If pressed again, the unit will revert back to previous settings. PUMP button (only on pump models) Use this button to activate the heavy-duty pump system for active drainage. ENGLISH 5 Display lights ON light When the STAND-BY button is pressed to start the unit, the ON light will come on automatically. The light will go off again when the unit is switched off. NOTE: After a power outage, the unit will not switch itself on again automatically. When the power supply has been reestablished, please press the STAND-BY button to start the unit again. TANK Warning light If the water tank is full, improperly positioned or missing, the tank warning light will start blinking. An alarm will sound until the tank is either emptied or correctly positioned into place. DEFROSTING light With an ambient temperature of less than 15°C, (59°F) the appliance performs defrosting cycles. While the appliance is defrosting, the defrosting light comes on and remains on until defrosting is completed. During the defrosting cycle only the following 4 keys are active: pump button, stand-by button, temperature button, timer button. PUMP light (only on some models) Once the pump button is pressed the pump light will switch on. If the pump light flashes it means that the pump is not functioning properly. Installation Instructions 1. Allow at least 12 inches (30cm) of space on all sides of the unit for good air circulation. 2. Install your dehumidifier on a floor, table, or shelf. When installing the unit on a table or shelf, make sure the table or shelf is strong enough to support the weight of the unit with a full bucket. Note: The dehumidifier needs to be secured when installed on a table or a shelf. Do not sit or stand on the dehumidifier. 3. The tank must be properly positioned. 4. Castor wheels let you move the dehumidifier easily. 12 in.(30 cm)12 in.(30 cm) Choosing the proper location for the unit 1. Use the unit in a basement to help prevent moisture damage. 2. Use the unit in cooking, laundry, bathing, and dishwashing areas that have excessive moisture. 3. Use the unit to prevent moisture damage anywhere books or valuables are stored. 4. Place the unit where you want to have comfortable conditions. List of components For models equipped with pump system: • 16 ft. (5 m) clear hose with Quick-Connect connection • 3 ft. (1 m) clear hose For all other models: • 3 ft. (1 m) clear hose Required tools and assembly time Collection tank: No assembly or plumbing necessary. Continuous draining outlet: To use the Continuous Draining feature the following tools will be necessary: • 5 mm (0.2 in.) drill bit (to drill open the draining outlet) • Drill tool The estimated assembly time is 1-2 minutes. Pump system and Quick-Connect 16ft. hose (only on models equipped with pump system): No tools necessary. The estimated assembly time is 1-2 minutes. ENGLISH 7 Disposing of the collected water A) Empty the tank manually. When the tank is full, remove (fig.1) and empty it into a sink. When finished, replace it properly. NOTE: The tank must be positioned properly. If you hear the intermittent sound of the beep, it means the tank is not in the proper position. B) Continuous draining. Condensed water can be drained via a hose connected to the outlet located in the lower part of the tank proceeding in the following way: 1. remove the water tank. 2. Using a 5 mm drill bit, (0.2 inches) drill a hole in the base of the tank along the torus as shown in figure 2. 3. Connect a hose to the hose connector (fig. 3). Be sure the hose does not kink or bend. Make sure that the hose is not higher than the hose connection (see figure 4). NOTE: When you remove the rubber cap keep it in a safe ...
Эта инструкция также подходит к моделям:Осушители воздуха - de 300 (154.93 kb)
Осушители воздуха - DE300P (154.93 kb)