Войти:
Оценок - 2, средний балл: 4 ( )

Инструкция по эксплуатации Buffalo Technology, модель LINKSTATION HD-HLAN

Производитель: Buffalo Technology
Размер: 861.88 kb
Название файла: dadf6ba0-0b51-423b-acda-7286bdf11230.pdf
Язык инструкции:en
Перейти к скачиванию



Фрагмент инструкции


Future user interfaces and software may be available for download from: (Support Section - Downloads). Due to the evolving state of the product, the images and text in this manual may vary slightly from the images and text displayed by your LinkStation. These changes are minor and should not affect the ease of setup. Table of Contents LinkStation Diagram...............................................4 LinkStation Quick Setup.........................................6 Link Navigator Setup ............................................12 Accessing LinkStation Data from a PC ..................21 Accessing LinkStation Data from a Mac ................24 LinkStation Expansion..........................................27 Basic Settings.......................................................28 Network Settings...................................................31 Security Settings...................................................35 USB Settings ........................................................43 USB Printer Installation .......................................47 Maintenance Settings............................................51 Restoring LinkStation Backups ..................... ......57 PCast/LinkTheater Settings .......................... ......62 Troubleshooting....................................................65 Technical Specifications........................................68 North American Technical Support .......................69 FCC and GPL .......................................................69 European Technical Support ............................... 70 LinkStation Diagram 1. Power Button – The Power Button is used to power the LinkStation on or off. The power on process will take approximately 30 seconds to a full minute to complete. During this time, do not unplug the LinkStation from the wall outlet. To turn the LinkStation off, press and hold the power button for several seconds until the Power LED light begins blinking. At that time, stop pressing the button and shutdown should complete within 30 seconds. 2. Power LED – The Power LED light will blink during startup or shutdown, but otherwise will remain lit up while LinkStation is powered on. 3. LINK/ACT LED – The LINK/ACT LED light will light up if an Ethernet Cable is plugged in that is attached to another device such as a router, hub, or PC. Periodically, the LED will blink. This blinking signifies network activity. LinkStation Diagram 4. Disk Full LED – When LinkStation’s internal drive approaches 95% of its capacity, the Disk Full LED will light up in red. For options to increase storage capacity, see LinkStation Expansion section on Page 27. 5. Diagnostic LED – The Diagnostic LED flashes if the LinkStation encounters an error. In this event, please contact our technical support. 6. USB Port (Front & Rear) – LinkStation offers two USB Ports for adding external drives or USB printers. Please see the LinkStation Expansion section on page 27 to learn more about how to take advantage of the USB Ports on LinkStation. Quick Setup Quick Setup Plug the LinkStation’s power cord into the back of LinkStation. Then, plug the other end of the power cord into a power outlet. Also, plug the included Ethernet Cable into LinkStation’s Ethernet Port located on the back of LinkStation. Quick Setup Quick Setup Connect the other end of the included Ethernet Cable into a hub, switch, or router on the network, or connect it directly to a nearby running PC. NOTE: It is recommended that you connect LinkStation to a hub or switch on your network. Connecting it directly to the back of a PC should only be used if absolutely necessary. Many features, including DHCP IP Addressing, require LinkStation to be connected to a switch or hub. Quick Setup Quick Setup Turn the LinkStation on by pressing the power button until the green Power LED begins to flash. Quick Setup Quick Setup Check the LINK/ACT light on the front of the LinkStation. If it is lit, then your LinkStation is connected properly; please turn to page 12 to continue setup. If it is not lit, continue to the next page. Quick Setup Quick Setup On the rear of the LinkStation, flip the black Cable Selection switch. This switch tells LinkStation whether to communicate over a Crossover or Patch cable. Verify that the LINK/ACT LED on the front of LinkStation is lit (see page 9’s picture). If it is lit, continue to page 12 to continue setting up LinkStation. If the LINK/ACT LED is still not lit, try moving the switch to the other position. If that doesn’t help, turn to the next page to check for common problems. 10 Quick Setup Having Problems? Make sure that: • Both LinkStation and the switch or PC are powered on. • The Ethernet Cable is securely fastened to both devices. • The Ethernet Cable is not damaged; verify this by trying another Ethernet Cable. • When verifying new cables, try the Cable Selection switch in both positions (see page 10). If problems persist, contact our technical s...


Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории