Оценок - 5, средний балл: 4 ( )

Производитель: ATN Размер: 403.73 kb Название файла: 79c01cbb-8e75-47ed-a02a-586fad8e286f.pdf Язык инструкции:

Notice the ability of the Aries scope to see in total darkness with the aid of the IR illuminator. OPERATING RETICLE BRIGHTNESS ADJUSTMENT MOUNTING 1. Slightly loosen the horizontal and vertical fixing screws on the 7/8” weaver rail built into the scope. 2. Place the scope on the dovetail mount of the fire arm making certain that the mount aligns FOCUSING To focus your riflescope you will need to adjust the diopter first thing. Simply turn the diopter clockwise until it stops. Then, while looking through the diopter at a subject, slowly turn the diopter back counter clockwise until the grain in the image is sharp. By rotating the knob you may adjust the reticle’s brightness. Adjustment could be easily seen if you look through the scope while adjustment. with the receptor attachment screw groove. Adjust as necessary. 3. Tighten the horizontal fixing screws. NOTE: Receptor attachment screws may need to be tightened after continuous shooting. NOTE: We suggest that you focus the diopter during daylight with the filter on. Before focusing turn the lens fixation handle clockwise, to unlock the lenses. Next, focus the front lens until the image and the grain are both sharp. When you are in the low-light conditions and the daylight filter is off you may focus the front lens to receive a sharp image, the diopter should not be adjusted. NOTE: The front lens should be readjusted as you view objects at different distances. When you are finished to adjust the front lens focus, you should lock the front lens in place by turning the lens fixation knob clockwise. Failure to do this may cause shift in aimpoint when shooting. ■ IS I I m -A i 3 IR ILLUMINATION Infra-red (IR) Illuminators are common for night vision technology. The IR light greatly enhances the performance of your Aries scope, while remaining almost totally invisible to the naked eye. In dark environment, power up the Aries scope. Now, find a scene and examine it without the IR on then with IR powered up. Note the difference in illumination. It is important to remember that the IR illuminator is simply an infra red light source, and like any light source it may loose its effectiveness over a great distance. To fix the IR Illuminator to the riflescope screw the thumb screw on the IR into the thread on the scope. To switch the IR on and to adjust the brightness rotate the rheostat located on the side of the Illuminator. The changes of adjustment could be observed while looking through the scope. The IR is off when the mark on the rheostat coincides with “0” on the scale. NOTE: The riflescope could be equipped with digitally controlled IR. The IR illuminator control buttons are located on its side. To switch the Digital IR illuminator on/off press “+” and “-” buttons simultaneously. When the IR illuminator is switched on you can see the green LED lit. By pushing the buttons “+” and “-” you may adjust the IR brightness. The IR beam is focusable to change the field of coverage. To change the beam width slightly turn the IR lens. You could change the IR control panel fitting your needs. The screw-tool included into the set should be used for weakening the fixing screw located on the IR. Rotate the IR placing at in the most convenient position. Tighten the screw with the screw-tool to fix the new position. Battery IR Brightness ' a Housing Adjustment w \ Etevatton ^ IR Focusing Fixation \ Screw IR Windage RANGEFINDE RETICLE The range finder reticle in your Night Vision Rif-lescopes was designed to assist you in determining the range of your target. These distances are based on a 6’ target. ARIES350/6800/7800 RETICLE A 6’ target fits between the numbered baseline (the three short horizontal lines directly next to the numbers) and the main horizontal line. If the 6’ target fits between the 1 and the right horizontal post of the main line the target is 100 yards away. If the same target fits between the 2 and the right post of main line the target is 200 yards away. The same is with the three, the target is 300 yards away. If a 6’ target fits If a 6’ target fits between these two between these two lines then the target lines then the target is 100 yards away. is 200 yards away. w TBS, —23_al -1 ARIES350/6800/7800 RETICLE A 6’ target fits between the numbered baseline and the main horizontal line. If the 6’ target fits between the 2 and the right horizontal post of the main line the target is 200 yards aw...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: