Оценок - 3, средний балл: 4 ( )

Производитель: ATN Размер: 403.73 kb Название файла: Язык инструкции:

Failure to do this may cause shift in aimpoint when shooting. ■ IS I I m -A i 3 IR ILLUMINATION Infra-red (IR) Illuminators are common for night vision technology. The IR light greatly enhances the performance of your Aries scope, while remaining almost totally invisible to the naked eye. In dark environment, power up the Aries scope. Now, find a scene and examine it without the IR on then with IR powered up. Note the difference in illumination. It is important to remember that the IR illuminator is simply an infra red light source, and like any light source it may loose its effectiveness over a great distance. To fix the IR Illuminator to the riflescope screw the thumb screw on the IR into the thread on the scope. To switch the IR on and to adjust the brightness rotate the rheostat located on the side of the Illuminator. The changes of adjustment could be observed while looking through the scope. The IR is off when the mark on the rheostat coincides with “0” on the scale. NOTE: The riflescope could be equipped with digitally controlled IR. The IR illuminator control buttons are located on its side. To switch the Digital IR illuminator on/off press “+” and “-” buttons simultaneously. When the IR illuminator is switched on you can see the green LED lit. By pushing the buttons “+” and “-” you may adjust the IR brightness. The IR beam is focusable to change the field of coverage. To change the beam width slightly turn the IR lens. You could change the IR control panel fitting your needs. The screw-tool included into the set should be used for weakening the fixing screw located on the IR. Rotate the IR placing at in the most convenient position. Tighten the screw with the screw-tool to fix the new position. Battery IR Brightness ' a Housing Adjustment w \ Etevatton ^ IR Focusing Fixation \ Screw IR Windage RANGEFINDE RETICLE The range finder reticle in your Night Vision Rif-lescopes was designed to assist you in determining the range of your target. These distances are based on a 6’ target. ARIES350/6800/7800 RETICLE A 6’ target fits between the numbered baseline (the three short horizontal lines directly next to the numbers) and the main horizontal line. If the 6’ target fits between the 1 and the right horizontal post of the main line the target is 100 yards away. If the same target fits between the 2 and the right post of main line the target is 200 yards away. The same is with the three, the target is 300 yards away. If a 6’ target fits If a 6’ target fits between these two between these two lines then the target lines then the target is 100 yards away. is 200 yards away. w TBS, —23_al -1 ARIES350/6800/7800 RETICLE A 6’ target fits between the numbered baseline and the main horizontal line. If the 6’ target fits between the 2 and the right horizontal post of the main line the target is 200 yards away. If the same target fits between the 5 and the right post of main line the arget is 500 yards away. The same is with the 1,3 and 4.The target would be either 100,300 and 400 yards away. The vertical lines in chevron reticle are proportioned to help in rangefinding and in making allowances for wind or movement. A between these two between these two lines then the target lines then the target is 500 yards away. is 200 yards away. 4 WINDAGE AND ELEVATION CLEANING THE EYEPIECE You may need to clean the eyepiece of the riflescope from time to time in order to guarantee top performance. When you receive your riflescope you should check for dust on the eyepiece of the unit. First you will need to remove the eyepiece. To do that you will need to initially loosen the 2 set screws that can be found on the base. Then unscrew the eyepiece counter-clockwise to remove it. The vertical and horizontal adjustments for the Aries can be achieved by turning the elevation and windage adjustment mechanisms (remove dust caps first). Each click equals 1/8 inch at 100 yards for the 350 and 6800/7800. 1/4 inch for the 330. When reaching the maximum range of rotation do not use force. NOTE: You do not have to remove the set screws completely, they are very small and easy to misplace. CAUTION: Use only Photographic lens cleaning tissue on these surfaces. Be careful not to scratch or smudge any of these surfaces. When using compressed air to blow dust away, make sure to avoid inverting the can while spraying. This can cause frozen propellant to exit the can, which can cause seri...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: