Оценок - 0, средний балл: 0
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
Screw Identification NOTICE: When reinstalling a screw, you must use a screw of the correct diameter and length. Make sure that the screw is properly aligned with its corresponding hole, and avoid overtightening. Screw Placement Map Hard Drive Door Security: M3.0 x 5 mm (1 each) Keyboard to Bottom Case Assembly: M2.5 x 20 mm (4 each; one in memory door and one in mini-PCI door) Display to Base: M2.5 x 6 mm (3 each; 2 at back of system; 1 at flex cable strain relief) Display Bezel: Rubber screw covers (4 each) Plastic screw covers (2 each) M2.5 x 4 mm (6 each) Display Panel to Display Mounting Bracket: M2.0 x 3 mm(6 each) Flex Cable Mounting Bracket to Top Cover: M2.5 x 4 mm (1 each) Video Graphics Board: M2.5 x 8 (3 each) Palmrest to Bottom Case Assembly: M2.5 x 20 mm (9 each) System Board: M2.5 x 4 mm captive washer (3 each) LED Board: M2.0 x 4 mm (2 each) Back to Contents Page Palmrest Bracket: M2.5 x 4 mm (2 each) M2.5 x 20 mm (1 each) Fan Assembly: M2.0 x 4 mm (3 each) RJ-11/RJ-45 Board Assembly: M2.5 x 4 mm (1 each) Back to Contents Page Removing and Replacing Parts Dell™ Latitude™ C810 Service Manual System Components Exploded View Hard Drive System Components Hard Drive Fixed Optical Drive Memory Module Mini PCI Card Assembly Keyboard Assembly Display and Bezel Assemblies Microprocessor Thermal Cooling Assembly Microprocessor Module Video Graphics Board Palmrest Assembly Reserve Battery System Board Assembly Battery and Modular Bay Latch Assemblies Battery Charger Board LED Board Fan Assembly RJ-11/RJ-45 Board NOTICE: Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell is not covered by your warranty. NOTICE: Unless otherwise noted, each procedure in this manual assumes that a part can be replaced by performing the removal procedure in reverse order. NOTICE: Disconnect the computer and attached devices from the electrical outlet and remove any installed batteries. NOTICE: To avoid ESD, ground yourself by using a wrist grounding strap or by periodically touching unpainted metal on the computer. NOTICE: The hard drive is very sensitive to shock. Handle it by its edges (do not squeeze the top of the case), and avoid dropping it. Hard Drive Removing the Hard Drive 1. Follow the instructions in "Preparing to Work Inside the Computer." 2. Remove the drive door screw. 3. Pull the hard drive out. Replacing the Hard Drive 1. Gently push the hard drive into the drive bay until the drive door is flush with the computer case. 2. Push down on the drive until it snaps into place. 3. Replace the screw in the hard drive door. Fixed Optical Drive Fixed Optical Drive Removing the Fixed Optical Drive 1. Follow the instructions in "Preparing to Work Inside the Computer." 2. Loosen the captive screw on the bottom of the computer. NOTICE: Disconnect the computer and attached devices from the electrical outlet and remove any installed batteries. NOTICE: To avoid ESD, ground yourself by using a wrist grounding strap or by periodically touching unpainted metal on the computer. 3. Turn the computer over, pull out the pull tab, and use the pull tab to remove the fixed optical drive. Memory Module Removing the Memory Module Cover Memory Module Cover 1. Follow the instructions in "Preparing to Work Inside the Computer." 2. Remove the screw. 3. Disengage the metal tabs at the opposite end of the cover. Memory Modules Removing the Memory Modules 1. Remove the memory module cover. 2. To release a memory module from its socket, spread apart the tabs at each side of the module until the module pops up slightly. NOTICE: To keep the pull tab from catching on the captive screw, turn the computer over before removing the fixed optical drive. NOTICE: Disconnect the computer and any attached devices from electrical outlets and remove any installed batteries. NOTICE: To avoid ESD, ground yourself by using a wrist grounding strap or by periodically touching unpainted metal on the computer. 3. Lift the memory module out of its socket. Replacing the Memory Modules 1. If you only have one memory module, install it in the socket labeled "DIMM A." Install a second memory module in the socket labeled "DIMM B." 2. Insert the memory module's edge connector into the socket slot at a 45-degree angle and press the module firmly into the slot. 3. Pivot the module down until it clicks into place. If you do not hear a click, remove the module and reinstall it. 4. Insert the metal tabs on the memory module cover into the bottom case assembly, rotate the cover down, and replace the screw. Mini PCI Card Assembly You must remove the optional Mini PCI Card assembly before the system board assembly can be removed. A Mini PCI Card assembly may consist of a modem, a NIC, a modem and NIC combination, or a wireless NIC. A modem, NIC, or modem and NIC combination must be connected to the wiring harness as appropriate; a wireless NIC must be connected to the system's internal antenna. Min...