Войти:
Оценок - 0, средний балл: 0 ( )

Инструкция по эксплуатации Dell, модель Inspiron 300m

Производитель: Dell
Размер: 1.62 mb
Название файла:
Язык инструкции:en
Перейти к скачиванию



К этому устройству также есть другие инструкции:

Фрагмент инструкции


NOTE: Each keyboard tray screw has an arrow beside it. 1 keyboard tray 2 M2 x 4-mm screws (5) 1. Replace the keyboard tray. 2. Route the antenna cables through the oval opening on the keyboard tray. 3. Reinstall the five M2 x 4-mm screws that secure the keyboard tray to the system board. Back to Contents Page 1 antenna cable connectors 2 oval opening on keyboard tray Back to Contents Page Mini Recommended Spares List Dell™ Inspiron™ 300m Service Manual NOTE: The part numbers listed below are subject to change. Bottom Plastics Assembly G0767 battery latch kit H0163 bottom LCD-cover assembly H0164 memory door T2913 bottom plastics assembly (TAA-compliant) U2737 bottom plastics assembly (non-TAA version) Power H2569 power cord, US, 0.9 m (3 ft) 5U092 AC power brick only, 65 W X0789 external battery charger kit, includes power cord H0286 rubber strap for power cord management M0270 primary battery, 4 cell, 14.8 V, lithium Y0037 external battery, 8 cell CD, CD-RW C0924 24X CD D0727 24X CD-RW DVD K2232 2X, DVD+RW, D-module R1695 8X DVD, SFX U1038 4X DVD+RW, D-module Y1565 24X CD-RW/DVD Combo Floppy Drive 1R159 floppy drive, D-module Hard Drive and Accessories N2902 20-G HDD N2903 30-G HDD U2407 40-G HDD (5400 RPM) T2445 60-G HDD (5400 RPM) Fan D2589 fan Keyboard 5Y730 keyboard, US Back to Contents Page Hinges G0810 left hinge cover H0192 right hinge cover J0045 12.1 LCD hinge up assembly Memory 3Y180 128-MB DIMM 3Y182 256-MB DIMM 0K963 512-MB DIMM 7N020 1-G DIMM Modem Y0231 56-K V2 internal modem System Board T2907 system-board service kit, 1.2 GHz, (non-TAA version) U2733 system-board service kit, 1.2 GHz (TAA compliant) Wireless 2U381 Bluetooth™ module, internal 9Y200 Intel® Pro 2100 802.11b H0294 PCMCIA card blank insert J0846 TM1300, 802.11b/g N0498 Intel 2.4 GHz Screws 2013T M2 x 3-mm screw 6K709 M2 x 5.5-mm screw 6R788 M2 x L4-crew 7T775 M3 x 5-mm screw 8T707 M2 x 6-mm screw 98MKC M2 x 4-mm screw Speaker 7C552 speaker, 1 each, left or right Palm Rest Assembly G0808 palm rest assembly Back to Contents Page Palm Rest Dell™ Inspiron™ 300m Service Manual Removing the Palm Rest Replacing the Palm Rest Removing the Palm Rest 1. Remove the battery. 2. Remove the keyboard. 3. Turn the computer over, and remove the three M2 x 4-mm screws from the bottom of the computer. 4. Turn the computer over, and open the display. 5. Remove the six M2 x 4-mm screws on the palm rest. CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Owner's Manual. NOTICE: Disconnect the computer and any attached devices from electrical outlets. NOTICE: To avoid ESD, ground yourself by using a wrist grounding strap or by touching an unpainted metal surface on the computer. NOTICE: Read "Before You Begin" before performing the following procedure. 1 M2X4 screw (3) 6. Lift up and rotate the palm rest forward. 7. Lift the ZIF connector, and disconnect the palm-rest flex cable from its ZIF connector on the system board. 8. Lift the palm rest up and out of the computer. Replacing the Palm Rest To aid with proper flex cable connection, a locator line has been added near the end of the palm-rest flex cable. When replacing the palm-rest flex cable, press the cable into the connector until the line aligns with the system board and hold it steady while you snap the ZIF connector down. (The locator line may reappear after the connector is closed, which should not indicate a problem with the connection.) 1 M2 x 4-mm screws (6) 1 palm rest flex cable 2 ZIF connector 3 palm rest Back to Contents Page Back to Contents Page Pin Assignments for I/O Connectors Dell™ Inspiron™ 300m Service Manual Pin Assignments for the Computer Pin Assignments for the Media Base Pin Assignments for the Computer USB Connector 2.0 Video Connector IEEE 1394 Connector Pin Signal 1 VCC 2 Data– 3 Data+ 4 GND Pin Signal Pin Signal 1 RED 9 CRT_VCC 2 GREEN 10 GND 3 BLUE 11 NC 4 NC 12 DAT_DDC2 5 GND 13 HSYNC 6 GND 14 VSYNC 7 GND 15 CLK_DDC2 8 GND Pin Assignments for the Media Base Docking Connector 1 TPB– 2 TPB+ 3 TPA– 4 TPA+ Pin Signal Pin Signal 1 DCK3_DOCK_IN2* 2 USB3_P2+ 3 SYS_DCIN* 4 USB3_P2– 5 VDC 6 GND 7 VDC 8 VGA3_RED 9 VDC 10 VGA3_GREEN 11 KBC3_ADID_CLK 12 VGA3_BLUE 13 GND 14 VGA5_DDCD 15 PIO3_SLCT 16 VGA5_DDCC 17 PIO3_AUTOFD* 18 VGA5_HSYNC 19 PIO3_ERROR* 20 VGA5_VSYNC 21 PIO3_INIT* 22 GND 23 PIO3_SLCTIN* 24 KBC3_EJECT* 25 GND 26 DCK3_RST* 27 PIO3_PD0 28 BATTB_PRES* 29 PIO3_PD1 30 BAT3_VOLTB 31 PIO3_PD2 32 KBC3_CHGENB 33 PIO3_PD3 34 KBC3_DCHGENB 35 PIO3_PD4 36 DCHGOUTB 37 PIO3_PD5 38 DBAT3_SMDATA 39 PIO3_PD6 40 DBAT3_SMCLK 41 PIO3_PD7 42 KBC3_DCKPWRON 43 PIO3_STROBE* 44 GND 45 PIO3_ACT* 46 PS25_KCLK 47 PIO3_BUSY 48 PS25_KDATA 49 PIO3_PE 50 PS25_MCLK 51 GND 52 PS25_MDATA 53 SIO3_DTR1* 54 P2.5V_LAN 55 SIO3_TXD1* 56 KBC3_ 57 SIO3_RTS1* 58 GND 59 SIO3_CTS1* 60 AUD3_SPDIF PS/2 Connector Parallel Connector 61 SIO3_R11* 62 DCK3_PWRSW* 63 SIO3_DSR1* 64 D_HP_IN 65 SIO3_DSR1* 66 CHP3_USBIDE_RST* 67 SIO3_DCD1* 68 DCK_VOLUP* 69 DCK_NICOMVDC ...


Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории