Lift the hook upward as shown in Figure 1. Twist the hook 180. ......................................................(counter clockwise) as shown in Figure 2.. Push the hook downward as shown in Figure 3. Hook the headset onto the desired ear. Adjust the angle of the headset until the microphone is pointing towards your mouth as shown in Figure 4. 180. Figure 2 Figure 1 Figure 3 Figure 4 Headset attachments Over-the-ear hook To remove the ear hook from the headset: Hold the headset with one hand

Before using this AT&T product, please read the Important safety information on pages 49-52 of this manual. Please thoroughly read the user’s manual for all the feature operations and troubleshooting information necessary to install and operate your new AT&T product. You can also visit our website at or call 1 (800) 222-3111. In Canada, dial 1 (866) 288-4268. Model #: TL7610 (Headset and headset base) TL7611 (Headset, headset base and handset lifter) Type: DECT 6.0 cordless headset Serial # : Pu

Twist and pull the headset until it separates from the ring of the neckband. Operation 17 Headset operation Making a call If you registered the expansion headset to a headset base, see the user’s manual for your headset base model TL7610/TL7611/ TL7650/TL7651 for additional instructions. Visit to view or download the user manuals. If you registered the expansion headset to an AT&T DECT cordless telephone: Follow the instructions in your telephone user’s manual for making calls. To switch to the

Page 5 Installation Instructions Step 3: Mount the eX.10’s display Twist the supplied round plastic plate to the base of the eX.10’s display, and attach the supplied double.sided tape to this plate. Clean the dash area where the eX.10’s display will be mounted with the supplied alcohol pad. Remove the backing from the double.sided tape, and attach it to the dash by pressing firmly*. Connect the monitor cable to the display base, and route the monitor cable to the desired location for the eX.10’s

• Before making sound interruption on the Bluetooth compatible device, make sure that INT MUTE is set to OFF. (Initial setting on the unit is OFF.) 2 Set “Bluetooth IN” or “Bluetooth” to ADAPTER*. (Refer to the Owner’s Manual of the connected units.) 3 Turn the ignition key off (ACC OFF) and on again (ACC ON). • Before using a hands-free phone, it must be paired with the adapter. Refer to “Bluetooth SETUP” (pages 4-5). * If “Bluetooth IN” or “Bluetooth” is set to OFF once, the communication to t

Press to mute the ring tone in the earpiece when there is an incoming call. Earpiece Microphone Battery cover Open to install or replace the battery. Quick reference guide - headset Headset alert tones Three quick beeps VOLUME /+ - keys are pressed when the volume is already at its highest or lowest setting. The headset is not registered and the headset ON/OFF button was pressed. The headset is out of range from the headset base during a call. One short beep every 20 seconds Low battery warning.

For optimal performance, charge the headset battery for at least six hours before use. When not in use, recharge the headset by returning it to the headset base. 1. Press on both sides of the battery compartment cover and lift the cover up and off. 2. Insert the battery into the battery compartment. 3. Push the battery plug into the connector inside the compartment and ..............................place the wires neatly inside the compartment. 4. Insert the tab on the bottom of the battery cove

2. Follow all warnings and instructions marked on the product. The symbol identifies and alerts the user to the presence of important operating and service instructions. 3. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 4. Do not locate base unit near water, for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement or near a swimming pool. 5. Do not place this product on an un

Products purchased the Canada are covered only in the Canada. Products purchased in the U.S.A. are covered only in the U.S.A. LENGTH OF WARRANTY: This Warranty is in effect for one year from the date of the first consumer purchase. LIFETIME TAPE HEAD WARRANTY: All Alpine Car Audio analog tape heads excluding Video tape heads are warranted for life against manufacturing defects causing failure. WHO IS COVERED: This Warranty only covers the original purchaser of the product, who must reside in the

Before installing your headset, you must notify the owner of the host equipment (i.e., leasing company). Provide them with the headset registration number. The registration number is printed on the headset registration label. 2. If the installation of your headset requires the installation of a headset jack/JackSet® that connects to the internal wiring of leased telephones or other devices, such connections can only be made with permission of the owner of the host equipment. 3. In case of troubl