Оценок - 4, средний балл: 4.8
(
)
)
|
Фрагмент инструкции
INTRODUCTION The interface adapter for iPod® by Clarion, EA1251, works by simulating the iPod as a 6 Disc CeNET CD Changer. Please consult your main unit's Owner's Manual for CD Changer operations before beginning to use EA1251. Clarion Multimedia Station of VRX series cannot control EA1251 through the KEY PAD screen or the list screen. If required so, please use the function buttons instead. Some EA1251 functions might not be available. Some main unit models with CD-Text function have the capability to show ID3 TAG if iPod is connected through EA1251. Please refer to Title Display Section for more details. For list of main unit compatible to EA1251, please consult your nearest Clarion dealer. For iPod operations, please refer to iPod Owner's Manual. 2. CAUTION Please check your iPod Owner's Manual for the operating temperature as leaving iPod in your vehicle might damage it due to temperature variations and moisture. 3 English English 3. CONNECTION Please consult your nearest Clarion dealer before attempting to connect EA1251 to your main unit and iPod. Improper connection might damage your main unit, EA1251, iPod or your vehicle wiring. Please make sure the Yellow wire (Bus power lead) is connected on the CeNET compatible Main Unit (This wire usually has a 3 Amp Fuse inserted) connects to battery. If this wire is not connected, the iPod interface will not function. Please refer to the wiring instructions for your CeNET Main Unit or contact your Clarion Dealer. Note: The C-Bus conversion adaptor (RCB-138) is not compatible with current system. 1. Connect the iPod to the CeNET compatible Main Unit. 2. Connect the iPod to the CeNET compatible Main Unit and CD Changer. iPod, iPod mini iPod connection cable (Included) CeNET compatible CD Changer (Sold separately) UE№= If user want to connect CD Changer together, please change address switch to No.2 CeNET compatible Main Unit (Sold separately) Y-adaptor for Multi-changer connection (CCA-519) o (Sold separately) □ To CeNET connector 4 4. INSTALLATION There are no moving parts in EA1251. However, caution must be taken to make sure minimum damage to the unit. Do not press, puncture or drop the unit at anytime. Install the unit where there is no direct sunlight, away from air condition ducts or high moisture areas and away from other vehicle electronic components. Using Velcro or 2-Sided Tapes Stick velcro or 2-sided tapes to the unit. Note: In case of using velcro or 2-sided tapes, make sure the unit will not fall down as this might damage the electronic component inside. Using Screw There are screw mounting holes in EA1251. Before drilling, make sure there are no hidden wires and parts that might be damaged. Improper wiring might damage EA1251, main unit and iPod. | (M4x14) 5 English English 5. OPERATION Start-up After connecting your iPod to the EA1251, the iPod display will change to the following: To start iPod operations, change the main unit mode to CD Changer mode. Playback will start automatically. The display changes from: Disc Check ^ Disc Repeat ^ Start Playing If the iPod is not connected, the main unit will display “No Magazine”. The main unit is unable to detect the presence of iPod if the battery of the iPod is flat. Please refer to the Playback section for detailed operation information. Disconnecting iPod automatically switches “on” after connecting to EA1251, and it's power is charged as long as it stays connected with the vehicle ignition key turn to ACC or ON. If vehicle ignition is turned to ACC off, playback is changed to pause, and iPod will go to power off mode in a few minutes. To switch off iPod manually, disconnect from EA1251 adaptor. Playback_ iPod buttons are disabled and the display is lock after it is connected to EA1251. All operations of the iPod are controlled from the main unit. Some iPod operations and features will be unavailable. Please read this manual carefully to optimize your iPod operations. To understand playback features better, please refer to PLAYLIST section. Default playback setting By default, the playback setting will be: • Start to play from DISC1 (All Songs Play) • Shuffle (Random) Off • DISC Repeat On When the iPod is connected, the main unit will initially display “DISC” and “RPT”. Songs number display During playback, the main unit will display the song number in sequence. However, only a maximum of two digits are displayed. If there are more than 99 songs in your iPod, only the last two digits will be displayed. For example, songs number 102 and 1002 will both be displayed as “02”. Play/Pause Press Play/Pause button on the main unit to play/ pause iPod playback. 6 Song (Track) Up/Down Press Track Up/Down button to jump from song to song. Short press Track Down button jumps playback to the beginning of current song. Short press Track button twice within 2 to 3 seconds jumps playback to the beginning of previous song. If the last song is...