Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
This will send the same sixteen audio channels being transmitted by the A-Net input module to the next A-Net device so that another unique monitor mix can be created. An unlimited number of A-Net devices can be connected in series using this method. Any A-Net device, including A-Net Distributors can be connected. DC Power Input Connect the DC power supply to the jack on the rear of the A-16R Personal Mixer. Use only power supplies designed for your Aviom products. When using the optional A-16D or A-16D Pro A-Net Distribution products, power can be supplied to the A-16R from a remote location eliminating the need for the local DC power supply. Consult the Distributor products’s documentation for additional setup information. Audio Outputs The audio outputs on the rear of the A-16R Personal Mixer can be used with any device that can accept a line-level audio output, such as wireless in-ear monitor transmitters, powered speaker systems, and recording devices. Balanced stereo and dual-mono outputs are available. Both XLR and 1/4-inch TRS jacks are available. Audio routing tip: Both sets of audio outputs (XLR and 1/4-inch) can be connected at the same time and routed to different audio devices. For example, a subwoofer could be connected to one set of outputs and a standard powered speaker system to the other. . Stereo Operation The XLR and TRS balanced line outputs on the rear panel of the A-16R Personal Mixer are independent of the front-panel headphone output signal. The mix appearing at each set of outputs is the same, but the setting of the Mono/Stereo switch only affects the rear-panel outputs. ................................ Mono Operation As mentioned previously, only the rear-panel audio outputs are affected by the Mono/Stereo switch. The headphone output on the front panel of the A-16R is always stereo. This allows the listener to have a stereo headphone mix while at the same time using a mono subwoofer to enhance low-end response. As an example, when performing live, a drummer can connect headphones to the front panel headphone output of an A-16R while at the same time the audio signal is connected to a mono amp and crossover combination being used to create a bass shaker system in the platform he is sitting on. To use a mono amplifier, powered speaker, subwoofer, etc., connect a standard audio interconnect cable (TRS or XLR type) from the audio output on the rear of the A-16R to the audio input on your mono device. For best results, set the Mono/Stereo switch to the Mono 39 Aviom A-16R and A-16CS User Guide position. Unbalanced audio devices can be connected to the A-16R Personal Mixer by using standard guitar-type (or tip-sleeve) cables. Balanced Inserts .................................................. The A-16R is equipped with a stereo insert send/return loop that can be used just like the insert points found in many mixing consoles. The audio signal from the A-16R can be sent to the inputs of an audio processor such as a compressor or limiter. The signal, once processed by the device, is then returned to the A-16R signal path via the Return jacks. The inserts on the A-16R are balanced. You can use either balanced or unbalanced audio processors with the A-16R. ............................ Audio from the A-16R is sent to the effect device’s inputs. The processed sound is heard when the signal from the effect is plugged into the A-16R Insert Return jacks. The audio signal will not be interrupted when a cable is patched into the Insert Send jack. You can use the Insert Send jacks as an additional 40 pair of audio outputs as long as no cables are connected to the Return jacks. Plugging a cable into the Return jack will interrupt the signal heard in the mix outputs (headphones and rear-panel line outputs) and will complete the signal path. Note: The insert Send/Return loop includes the auxiliary Mix In signal in the processing path. Signal Flow As seen in the diagram below (from left to right): • A-Net audio is mixed using the A-16R • Signals from the stereo Mix In jacks are mixed in with the sixteen-channel A-Net mix • The mix goes to the Insert Send/Return loop • An effects device processes the mix and returns the result to the A-16R via the Return jack • The processed signal from the Insert is combined to create the final mix that you hear ....................................... . ........... . ........... . ....................... .................................. Mix In The A-16R includes a convenient auxiliary stereo mix input. The input has its own front-panel level control. Signals connected to the Mix In are added to the stereo mix in the analog domain, at the point where the digital mix is converted back to an analog signal. Aviom A-16R and A-16CS User Guide .............................. Any analog line-level signal can be connected to the Mix In jacks. Some ideas for connected signals to the Mix In jacks include: • Click Tracks • Talkback or intercom communications • Pre-recorded tracks...
Эта инструкция также подходит к моделям:Музыкальные инструменты - A-16CS (1.97 mb)