Оценок - , средний балл:
(
)
)
Производитель: DeVillbiss Air Power Company
Размер: 105.21 kb
Название файла:
Язык инструкции:
Документ загружается, подождите пожалуйста
 |
Документ загружается, подождите пожалуйста
Фрагмент инструкции
@ 7000 RPM’s Maximum Working Pressure 90 PSI Air Inlet 1/4” NPT Recommended Hose Size 3/8” I.D. Minimum CFM Required @ 90 PSI 8 CFM (25% usage) #1 Approximately 150 ft./lbs. Torque #2 Approximately 190 ft./lbs. Torque #3 Approximately 210 ft./lbs. Torque #4 Approximately 230 ft./lbs. Torque TORQUE REGULATOR KNOB 1 3 4 2 Lubrication Air tools require lubrication throughout the life of the tool. The air motor and bearing uses compressed air to power the tool. Because moisture in compressed air will rust the air motor, you must lubricate the motor daily. An inline oiler is recommended. To lubricate the air motor manually: 1. Disconnect the tool from the air supply holding it so the air inlet faces up 2. Hold the trigger down and put one teaspoon of air tool oil in the air inlet (use SAE #10 weight oil if air tool oil is not available). Holding the trigger down helps circulate oil in the motor. 3. Connect the tool to an air source, cover the exhaust port with a towel and run for a few seconds. Any excess oil in the motor is immediately expelled from the exhaust port. Always direct exhaust port away from people or objects. Air Supply Recommended Air Compressor: 3/4 HP tank for intermittent use - 1.5 HP or larger for heavier duty use. Air hose should be at least 3/8" I.D. Pipe and fittings between compressor and air hose should be at least 1/2" nominal size. (5/8 I.D.). Be sure piping is free of droops and sags where moisture can accumulate. *The use of air filters and air line lubricators is recommended. Operation Before each use, drain water out of air compressor tank and condensation from air lines. After clearing air compressor moisture and lubricating tool, connect tool to an air hose of recommended size. Check air pressure. This tool operates at a maximum 90 PSI pressure. Set torque regulator, see chart, to set the desired setting to avoid over tightening and possible damage. Forward and reverse direction are controlled by pushing the button noted. Depress the trigger to operate tool. Impact wrench sockets and accessories must be . used with this tool. Do not use hand sockets and . accessories. D21543 4 — ENG MODEL 919.19008 3/8” AIR RATCHET WRENCH OPERATING INFORMATION SPECIFICATION CHART Free Speed 150 RPM (Forward/Reverse) Maximum Working Pressure 90 PSI Air Inlet 1/4" NPT Recommended Hose Size 3/8" I.D. Minimum CFM Required @ 90 PSI 5.5 CFM (25% usage) Torque Delivered @ 150 RPMS 45 Ft./Lbs. Follow instructions for lubricating and changing accessories. Maintain tools with care. Lubrication Air tools require lubrication throughout the life of the tool. The air motor and bearing uses compressed air to power the tool. Because moisture in compressed air will rust the air motor, you must lubricate the motor daily. An inline oiler is recommended. To lubricate the air motor manually: 1. Disconnect the tool from the air supply holding it so the air inlet faces up 2. Hold the throttle lever down and put one drop of air tool oil in the air inlet (use SAE #10 weight oil if air tool oil is not available). Holding the throttle lever down helps circulate oil in the motor. 3. Connect the tool to an air source, cover the exhaust port with a towel and run for a few seconds. ANY EXCESS OIL IN THE MOTOR IS IMMEDIATELY EXPELLED FROM THE EXHAUST PORT. ALWAYS DIRECT EXHAUST PORT AWAY FROM PEOPLE OR OBJECTS. *Failure to lubricate the tool at the air inlet will void your warranty. Air Supply Recommended Air Compressor: 1 HP tank for intermittent use - 1.5 HP or larger for heavier duty use. Air hose should be at least 3/8" I.D. Pipe and fittings between compressor and air hose should be at least 1/2" nominal size. (5/8 I.D.). Be sure piping is free of droops and sags where moisture can accumulate. *The use of air filters and air line lubricators is recommended. Operation Before each use, drain water out of air compressor tank and condensation from air lines. After clearing air compressor moisture and lubricating tool, connect tool to an air hose of recommended size. Check air pressure. This tool operates at a maximum 90 PSI pressure. The throttle control lever provides instant response when depressed. The reverse button is located in the ratchet housing and determines the direction of rotation. When driving a fastener to the point that the ratchet stalls, further tightening can be accomplished by operating the air ratchet in the same manner as a manually operated ratchet. Impact wrench sockets and accessories must be used with this tool. Do not use hand sockets and accessories. 5 — ENG D21543 SERVICE NOTES SERVICE NOTES D21543 6 — ENG SERVICE NOTES SERVICE NOTES 7 — ENG D21543 General General Manual Air Tool Set For the repair or replacement parts you need Call 7 am - 7 pm, 7 days a week 1-800-366-PART (1-800-366-7278) MODEL NO. 919.19007 FULL ONE YEAR WARRANTY AIR TOOL If this air tool fails due to a defect in material or workmanship within one year from the date of purchase, RETURN IT TO THE ...
Эта инструкция также подходит к моделям:Насосное оборудование - Companion D21543 (105.21 kb)