Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
Sufficient pipe would be used to prevent this from happening. 3. LOW FLOW OR PRESSURE a) Check suction piping for leaks. b) Check the impeller for clogging. Remove all foreign material if it is clogged. 4. NOISE a) Make sure pump and piping are supported. b) Make sure suction lift does not exceed 20 ft.(6mm) c) Check disch. piping for excessive bends or elbows. d) Check motor bearing for damage. HP Voltage Branch Max. Loads Amperes Fuse Rating Amperes Maximum Length of Cable Size Shown 50’ 100’ 200’ 300’ 400’ 500’ 1/2 115 8.6 15 14 14 10 8 8 8 230 4.3 15 14 14 14 14 14 12 3/4 115 13.2 20 12 12 8 6 6 4 230 6.6 15 14 14 14 12 12 10 1 115 16.2 25 12 10 8 6 4 2 230 8.1 15 14 14 14 12 10 10 1-1/2 115 20.8 30 10 10 8 6 4 2 230 10.4 15 14 14 12 12 10 8 2 115 21 30 10 10 6 6 4 2 230 10.5 15 14 14 12 12 10 8 2-1/2 115 23 35 10 8 6 4 2 2 230 11.2 15 14 14 12 12 10 8 PARTS FOR MODELS DDD/DDS SERIES- END SUCTION CENTRIFUGAL PUMPS 14 9 #6 Case Kit 8 #7 Base Kit 2 #5 Impeller Kit 3 4 5 12 13 11 Figure No. Part No. Cast Iron Part No. Stainless Steel Description 2 11-1498-04-R Seal Plate Cast Iron #11293 for DDD, RCFC 11-0063-01-R Seal Plate Stainless Steel for DDS 3 47-0258-53-02PK 47-0258-53-02PK Square-Ring Kit 6 x 1/8 x 1/8 (2 per kit) 4 10-0002-06 Mechanical Seal 5/8 for DDD, RCFC Models 10-1436-18 Mechanical Seal 5/8 Viton for DDS Models All Impeller Kits include: impeller, sq.-ring, mech. seal, wear-ring, & fasteners.-Fig. #’s. 3,4,5,12,13 5 05-3886-08-K 05-3886-16-K 1/2HP Impeller Kit 4.605 dia. #11375 05-3887-07-K 05-3887-15-K 3/4HP Impeller Kit 5.0 dia. #11376 05-3888-06-K 05-3888-14-K 1HP Impeller Kit 5.25 dia. #11377 05-3889-05-K 05-3889-13-K 1.5HP Impeller Kit 5.315 dia. #11378 05-3890-02-K 2HP Impeller Kit 5.65 dia. #11338 05-3891-01-K 2.5HP Impeller Kit 5.95 dia. #11379 Impellers for Units with Three-Phase Motors 5 05-9646-05-R 05-9646-05-R 1/2HP Impeller 4.605 dia. #11375 05-9650-00-R 05-9650-00-R 3/4HP Impeller 5.0 dia. #11376 05-9652-50-R 05-9652-50-R 1HP Impeller 5.25 dia. #11377 05-9653-15-R 05-9653-15-R 1.5HP Impeller 5.315 dia. #11378 05-9656-50-R 05-9656-50-R 2HP Impeller 5.65 dia. #11338 6 03-0850-08-R 03-0850-17-R Case Assembly Kit #11337 w/ plugs #11 for 1/2HP thru 1.5HP 03-0851-07-R Case Assembly Kit #11338 w/ plugs #11 for 2HP 03-0852-06-R Case Assembly Kit #11338 w/ plugs #11 for 2.5HP 7 12-1057-06-R 12-1057-06-R Base Assembly Kit w/ motor pad #8 for 48 frame mtr. 12-1060-03-K 12-1060-03-K Base Assembly Kit w/ motor pad #8 for 56 frame mtr. 9 & 13 14-4434-02-K 14-4434-02-K *Fastener Kit 11 31-0059-11-06PK 31-0059-11-06PK Plug Kit 1/4” Galv. (6 per kit) 12 08-0845-19-06PK 08-0845-19-06PK Wear-Ring Kit (6 per kit) 13 14-4353-09 14-4353-09 Capscrew 1/4-20 x 1-3/16 LG LH Hx. / Wash. for 2HP 3 Ph. 14-4354-08 14-4354-08 Capscrew 1/4-20 x 7/8 LG LH Hx. / Wash. for 1/2 thru 1.5HP 3 Ph. 14 Motor Motor See Motor Selection Page *Fastener Kit #14443402-K includes the following: 4 each 3/8-16 x 1-1/8 PL Hex Capscrews #9 1 each 1/4-20 x 1-3/16 Hex Wash-Capscrews for 1/2HP thru 1.5HP 3Ph. #13 1 each 1/4-20 x 1-3/6 Hex Wash-Capscrews for 2HP 3Ph. #13 U.S. LIMITED WARRANTY* Franklin Pump Systems, Inc. Franklin Pump Systems, Inc. warrants its new products to be free of defects in material and workmanship for a period of 1 year from date of installation or 2 years from date of manufacture, whichever comes first, WHEN installed in a domestic water systems application and pumping potable water only. Warranty does not cover applications pumping saltwater or other corrosive liquids. Consult and adhere to local codes for all applications. Franklin Pump Systems, Inc. also provides additional warranty coverage on specific products as specified herein. Franklin Pump Systems’ warranty obligation with regard to equipment not of its own manufacture is limited to the warranty actually extended to Franklin Pump Systems by its suppliers. This warranty extends only to the original retail purchaser and only during the time in which the original retail purchaser occupies the site where the product was originally installed. Requests for service under this warranty shall be made by contacting the installing Franklin Pump Systems dealer (point of purchase) as soon as possible after the discovery of any alleged defect. Franklin Pump Systems will subsequently take corrective action as promptly as reasonably possible. Franklin Pump Systems at its discretion may replace or repair any product that fails under this warranty after inspection by an authorized company representative or after Franklin Pump Systems has received the product at our factory. Replacement or repair cannot be made until after the product is inspected. All charges or expenses for freight to and from the factory, removal and reinstallation of the product, or installation of a replacement product are the responsibility of the purchaser. THIS WARRANTY SUPERSEDES ANY WARRANTY NOT DATED OR BEARING AN EARLIER DATE. ANY IMPLIED WARRANTIES WHICH THE PURCHASER MAY HAVE, INCLU...
Эта инструкция также подходит к моделям:Насосное оборудование - DDS Series (122.31 kb)