Оценок - 3, средний балл: 3
(
)
)
|
Фрагмент инструкции
. . . . . . . . . . . !". . . Roberts-Gordon Roberts-Gordon 1250 William Street 76 Main Street West, Unit 10 P.O. Box 44 Grimsby, Ontario, L3M 1R6 Buffalo, New York 14240-0044 Canada Telephone: 716.852.4400 Telephone: 905.945.5403 Fax: 716.852.0854 Fax: 905.945.0511 Toll Free: 800.828.7450 Quality in Any Language™ © Copyright 2004 Roberts-Gordon P/N 127200NA Rev. F 12/04 TABLE OF CONTENTS SECTION 1: Heating System Safety ............................1 1.1 Manpower Requirements ...................................1 SECTION 2: Installer Responsibility............................2 2.1 Corrosive Chemicals...........................................2 2.2 National Standards and Applicable Codes .........2 SECTION 3: Unpacking the Pump ...............................2 3.1 Open Shipping Cartons ......................................2 SECTION 4: Major Components ..................................3 4.1 Standard Parts List.............................................4 SECTION 5: Pump Installation .....................................6 5.1 Pump Assembly Instructions ..............................6 5.2 Pump Suspension ..............................................9 5.3 Condensate Trap and Condensate Tee ............11 SECTION 6: Motor Wiring...........................................12 6.1 Prior to Operation .............................................12 SECTION 7: Venting....................................................13 7.1 General Venting Requirements.........................13 7.2 Venting the Pump .............................................13 7.3 Horizontal Venting ............................................13 7.4 Vertical Venting.................................................15 SECTION 8: Servicing Instructions ...........................16 8.1 Pre-Season Maintenance and Annual Inspection .............................................16 8.2 To Change the Motor and/or the Impeller .........16 8.3 Maintenance Checklist .....................................17 SECTION 9: Replacement Parts and Accessories ...18 9.1 Replacement Parts...........................................18 9.2 Accessories ......................................................18 SECTION 10: Specifications.......................................19 SECTION 11: The ROBERTS GORDON® EP-200 SERIES PUMP Limited Warranty .......21 . ! ! . !" # # # . # # " . $! "% . Printed in U.S.A. TABLE OF FIGURES Figure 1: Major Component Descriptions .......................3 Figure 2: Pump Discharge Orientation / Impeller Rotation Direction ..............................6 Figure 3: Pump Assembly...............................................7 Figure 4: Motor Shaft Seal Assembly..............................8 Figure 5: Wall Bracket Assembly ....................................9 Figure 6: Wall Mounting Angle Assembly........................9 Figure 7: Wall Mounting ................................................10 Figure 8: Mounting Platform Assembly .........................10 Figure 9: Condensate Check Valve...............................11 Figure 10: Condensate Tee - Discharge Side ...............11 Figure 11: EP-201 Motor Wiring ...................................12 Figure 12: EP-203 Motor Wiring ...................................12 Figure 13: Side Wall Venting.........................................14 Figure 14: Vertical Venting ............................................15 SECTION 1: HEATING SYSTEM SAFETY SECTION 1: HEATING SYSTEM SAFETY Your Safety is Important to Us! This symbol is used throughout the manual to notify you of possible fire, electrical or burn hazards. Please pay special attention when reading and following the warnings in these sections. Installation, Service and Annual Inspection of heater and pump must be done by a contractor qualified in the installation and service of gas-fired heating equipment. Read this manual carefully before installation, opera tion or service of this equipment. This heating system is designed for heating nonresidential indoor spaces. Do not install in residential spaces. These instructions, the layout drawing, local codes and ordinances, and applicable standards that apply to electrical wiring, venting, etc., must be thoroughly understood before proceeding with the installation. Thin sheet metal parts, such as the various venting components, have sharp edges. To prevent injury, the use of work gloves is recommended. Do not attempt to operate the pump until all steps of the installation have been accomplished. 1.1 Manpower Requirements To prevent personal injury and damage to the pump, two persons will be required for installation. EP-200 SERIES PUMP INSTALLATION, OPERATION AND SERVICE MANUAL SECTION 2: INSTALLER RESPONSIBILITY The installer is responsible for the following: • To install t...
Эта инструкция также подходит к моделям:Насосное оборудование - EP-203 (2.23 mb)