FULLY 1NSERT. ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES. INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQ’ AU FOND. f The lightning flash with the arrowhead symbol, wiihin an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage’ wiihin the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral

In this way, you can avoid damage to the connected devices. When you are connecting or removing the cables from the inputs or outputs ofthe XR-3, first make sure that the level of the input faders or volume controls of the connected channels is set to "0." • Even when you turn the power svyitch off (STANDBY) while the AC adaptor is connected, a small current always flows through the AC adaptor. Therefore, be sure to remove the AC adaptor when you are not going use the XR-3 for an extended peri

All other servicing should be referred to qualified service personnel. Introduction Thank you for purchasing the Fostex X-55. The X-55 is a multitrack recorder with four inputs (two of which accept mic signals and can be specified as balanced or unbalanced inputs), a multi-function mixer, and a high-quality high-speed (9.5 cm/s) four-track cassette recorder. The X-55 allows you to create multi-track recordings using techniques such as track bouncing, punching in and out by footswitch, and usi

Let’s assume we have finished recording on tracks 1 ~3 in Step 1. Now, if another sound (vocal) is recorded on track 4 by the method in the Basic Operation, you will not be able to record any other sound source. Therefore, if you should utilize the remix feature of the X-30 to mix tracks 1 - 3, you will be able to make a new recording (Step 2). This technique is called “Ping-pong recording.” It is literally bouncing sound between tracks of this recorder. Next, tracks 1 and 2 are combined and rec

Since the AUX SEND signal is mono, the tape tracks will all be heard in the center of the stereo image. — General Suggestions — • Record and mix at relatively low sound levels. The longer your recording or mixdown session, the less accurate your hearing will be. Listening to playback at high volume for even short periods of time reduces your ability to hear high frequencies. The less high frequencies you hear, the more you tend to boost them, until you have a recording that is all highs. If yo

(Use the output volume on the bass so that the level is not too high.) Use the LINE OUT knob to adjust the headphone volume to an appropriate level. 4. After you set the recording level, play back the tape from the [000] point and rehearse your bass accompanying the drum machine recording on Track 1. Use the Playback fader 1 and the Playback PAN knob 1 to adjust the monitoring level and balance of Track 1 (drum machine). 5. When you finishing the rehearsal, rewind the tape to the [000] point.

2. Mix the signals recorded on tracks 1 through 6 and record the mixed signal onto tracks 7 and 8. Then tracks 1 through 6 can be used to record other materials. This is the basic technique used for Multitrackers. We recommend that tracks 7 and 8 are basically used as the destination tracks of “track bounce” from tracks 1 through 6. See “Advanced Operation” for details about the track bounce technique. In addition, tracks 7 and 8 play an important role in “training mode” and “mastering mode” des

[INPUT SEL] Key * Set whether to send the A to H input signals [INPUT] or track 9-16 play [TRACK] sounds to the faders of channel faders 9 to 16. 26. [REC ASSIGN-BUSS-SOURCE] Key * Select the channel (SOURCE) to send to the REC BUSS during “BUSS” recording. Select the SOURCE channel with the [CH STATUS/CH SEL] key. * This key lights ON when the SOURCE is selected. 27. [REC ASSIGN-BUSS-REC TRK] Key * The track (READY) to record in “BUSS” recording is selectable when this key is flashing. Set READ

DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Tne iighinng flash with arrownead symbol, within an equilateral triangle, is intended to alori the user to the presence of uninsulated "dangerous voltage" within me product's enclosure lhat may be of sufficient magnitude to constitute a risk ot electric shock to persons The exclamation pont withm an eauiiatera: triangle is intended to alert the user to the oresonce ot important op