Оценок - 3, средний балл: 3.3
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
1 Connect the included speaker and your instruments to the mixer. Connect the included speaker (300S) to the SPEAKER jack. Connect the sources (microphone, other instruments) to the input jacks. For details, see “Connection Example.” Before connecting any devices, make sure to turn off the power for all devices (including microphones). Also, before turning the power on or off, set the volume levels on all devices to minimum. NOTE: For best results when connecting an electric guitar or bass guitar to the mixer, use a direct box, preamp (guitar amp), or amp simulator. 2 Set the mixer’s LEVEL controls and MASTER LEVEL control to the minimum (zero). 3 Depending on the device used, set the MIC/LINE switch to MIC ( ) or LINE ( ) as appropriate. For low-level signals (such as that of microphones), set the switch to the MIC ( ) position. For high-level signals (such as keyboard instruments and audio equipment), set the switch to the LINE ( ) position. 4 Turning the power on First, turn on the power to any connected devices, then turn the STAGEPAS 150M power on. If you’ve connected powered speakers to the mixer, turn on the power of the mixer first, then the powered speakers. To avoid any loud, unexpected noise from the speakers, first turn on the power to those connected devices that are closest to the sound source. Example: Sound source (CD player or instrument) > STAGEPAS 150M > (Power amplifier) When turning off the power to the system, reverse the order described above. 5 Set the MASTER LEVEL control to the optimum position (indicated by the arrow). 6 While playing your instrument or singing into the microphone, adjust the LEVEL control of the corresponding channel. Adjust the LEVEL Control of the corresponding channel so that the “0” LED lights up momentarily. 7 Use the MASTER LEVEL control to adjust the overall volume. If the LIMITER indicator flashes continuously, the internal power amplifier section is being excessively overloaded and may malfunction. Applying reverb or echo to the sound Reverb recreates the warm ambience of an actual performance space, such as a concert hall or a night club. 1 For each channel you want to apply reverb, set the corresponding REVERB switch to ON ( ). 2 Use the REVERB control to adjust the overall reverb. Quick Guide Connection Example 1 Controls and Functions Caution Caution Caution ( SPEECH/MUSIC switch Set this switch to SPEECH ( ) to optimize the mixer settings and sound quality for speech purposes and announcements. Set this to MUSIC ( ) to optimize the mixer for musical performance. The switch lights up in yellow when it is set to MUSIC ( ). ^ LEVEL control Use these controls to adjust the volume balance among the various channels. To reduce noise, set any LEVEL controls on unused channels to the minimum. & MASTER LEVEL Control Determines the volume of the signal output from the SPEAKER jack. This allows you to adjust the overall volume without changing the relative volume balance among the various channels (made with the LEVEL controls) or the tone settings (made with the Equalizer). Caution # REVERB switch Set this switch to ON to recreate the rich ambience of various performance environments, such as a concert hall or a night club. The switch lights up in green when REVERB is ON ( ). $ REVERB control Determines the overall level of the reverb or echo that is applied to the output signal. For best results, this level should not be set very high, to avoid possible feedback and to prevent the sound from becoming “muddy” with too much reverb. @ Equalizer HIGH: Determines the level of the high frequency band for each channel. Rotating the knob clockwise boosts the high frequencies and produces a clearer, crisper sound. If you start getting feedback (a high-pitched squealing sound) or you want to make the sound softer and less harsh, turn the knob counterclockwise slightly. LOW: Determines the level of the low frequency band for each channel. Rotating the knob clockwise boosts the low frequencies and produces a deeper, warmer sound. If you start getting feedback or you want to make the sound less boomy, turn the knob counterclockwise slightly. 3 SPEAKER jack (for included speaker 300S only) This outputs the mixed monaural L+R signal channels from 1 to 7/8 and the level is adjusted with the MASTER LEVEL control. Connect only the included speaker (300S). 4 ST LINK OUT R jack This outputs signals from R (even) channels only. When inserting a plug to this jack, only signals from the L (odd) channels are supplied to the SPEAKER jack. The output level is adjusted with the MASTER LEVEL control. Used with the SPEAKER jack, this lets you output the signals in stereo from the speakers. 5 PHONES jack This outputs the mixed signal channels from 1 to 7/8, and the level is adjusted with the PHONES control. Connect a set of headphones here. 6 ST SUB OUT L (MONO) / R jacks These output the mixed signal channels from 1 to 7/8, and the level is adjusted with the ST SUB OUT control. You can ...