Оценок - 4, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
Together with a specially voiced 8” speaker, the 5 watt Mini Colossal has a vintage tone that really rocks. It can run clean, crunchy, or, down and dirty. Its unique design makes it easy to get a good tone fast, and its size makes it very practical. Whether practicing, recording, or, even playing a small gig, this lively little amp really sounds great. Before you begin playing through your amplifier, it is very important to ensure that the product has the proper AC line voltage supplied. You can find the proper voltage for your amp printed next to the IEC line (power) cord on the rear panel of the unit. Each product feature is numbered. Refer to the front panel diagram in this manual to locate the particular features next to its number. Please read this guide carefully to ensure your personal safety as well as the safety of your amplifier. FEATURES: • Single Input • 1 x 12AX7 and 1 x EL84 tube • Pure Class A operation • No negative power amp feedback • Preamp Volume and Tone controls • 5W (rms) into 4, 8, or 16 Ohms (selectable impedance) • Power Sponge™ output power level attenuator • Buffered Effects Loop Send and Return jacks • Classic opto-electronic Tremolo circuit • Microphone Simulated XLR Recording Output • XLR Ground Lift switch • Specially voiced 8” C8R-type speaker • Classic jeweled pilot light • Chrome plated brass control knobs VENTILATION: For proper ventilation, allow 24" clearance from nearest combustible surface. INPUT This 1/4” jack is designed to accommodate signals from any standard electric guitar. VOLUME This control sets the overall volume and preamp drive level of the amp. For best results, set this control to the maximum desired amount of preamp distortion and use the volume knob on your guitar to achieve cleaner tones. TONE This control sets the overall frequency response of the preamp. Rotate this control counterclockwise for darker sounds and clockwise for brighter sounds. EFFECTS SEND This buffered output provides a low-level signal to external effects processors. The Effects Loop is out of the signal path when it is not being used. EFFECTS RETURN This input provides a low-level signal return from external effects processors. SPEED This control sets the rate at which the Tremolo circuit modulates the signal. DEPTH This control sets the intensity with which the Tremolo affects the signal. POWER STATUS LAMP This indicator illuminates when mains power is being supplied to the amp. POWER SWITCH This heavy-duty two-way toggle switch applies mains power to the unit. The red POWER STATUS LAMP (8) will illuminate when this switch is in the ON position. CAUTION: The on/off switch in this unit does not break both sides of the primary mains. Hazardous energy can be present inside the chassis when the on/off switch is in the OFF position. Front Panel 9 5 7 6 4 3 2 1 8 1 2 3 4 5 6 7 8 9 IEC MAINS CONNECTOR This is a standard IEC power connector. An AC mains cord having the appropriate AC plug and ratings for the intended operating voltage is included in the carton. The mains cord should be connected to the amplifier before connecting to a suitable AC outlet. U.S. DOMESTIC AC MAINS CORD The mains cord supplied with the unit is a heavy-duty, 3-conductor type with a conventional 120 VAC plug with ground pin. If the outlet used does not have a ground pin, a suitable grounding adapter should be used, and the third wire should be grounded properly. Never break off the ground pin on any equipment. It is provided for your safety. NOTE: FOR U.K. ONLY If the colors of the wires in the mains lead of this unit do not correspond with the colored markings identifying the terminals in your plug, proceed as follows: (1) The wire that is colored green and yellow must be connected to the terminal that is marked by the letter E, the earth symbol, colored green, or colored green and yellow. (2) The wire that is colored blue must be connected to the terminal that is marked with the letter N or the color black. (3) The wire that is colored brown must be connected to the terminal that is marked with the letter L or colored red. POWER SPONGE™ This unique control allows the user to adjust the nominal output power level of the amplifier. It can be used in conjunction with the VOLUME (2) control to attain infinite combinations of power amp and preamp distortion at any volume level. This control DOES NOT affect the level of the Microphone Simulated Recording output and provides an appropriate load to the amplifier at all settings. SPEAKER OUTPUTS These paralleled 1/4" mono (TS) jacks are provided for the connection of speaker enclosure(s). Minimum speaker impedance is 4 Ohms. The CABINET IMPEDANCE SELECTOR switch (13) must be set to match the load of the speaker cabinet(s). The internal speaker is 8 Ohms. CABINET IMPEDANCE SELECTOR This three-position switch allows for appropriate selection of speaker cabinet impedance. If two enclosures of equal impedance are used, the switch should be set to half the individual value...
Эта инструкция также подходит к моделям:Музыкальные инструменты - JSX JSXTM Mini ColossalTM Class A Tube Guitar Amplifier (1.95 mb)