Оценок - 3, средний балл: 3.3
(
)
)
|
Фрагмент инструкции
* To assemble the unit, make sure you have the following four packages: -- RS85A (Electronic Drum Rack) -- DTP502 (Pad Set) -- DTX500 (Trigger Module) -- XP100SD (3-zone Drum Pad) NOTICE Before assembling the unit, lay a drum mat (sold separately). Before assembling the unit, lay a drum mat on the floor. Alternately, to prevent damaging your floor, lay the cardboard of the included packages, etc. on the floor before assembling the two parts shown in the circles in Figure 1. Figure 1: Unit Standard Assembly q DTX500 (Drum Trigger Module) w RHH135 (Real Hi-Hat Pad) e XP100SD (3-zone Drum Pad) r HS650A (Hi-Hat Stand) t AC Adaptor y PCY135 (3-zone Cymbal Pad) u PCY155 (3-zone Cymbal Pad) i TP65 (Drum Pad) o KP65 (Kick Pad) !0 RS85A (Electronic Drum Rack) Checking the contents of RS85A Open the RS85A (Electronic Drum Rack) package and confirm the contents. Figure 2: Electronic Drum Rack RS85A RS85A (1) Rubber Foot (2) Cable Band (6) *1 Assembly Manual (1) *2 --RS85A *1 Use cable bands to bind cables to pipes in “ Connecting to a power source”. (Spare bands are included.) *2 Not this manual. Assembling the Electronic Drum Rack 1 Take out the electronic drum rack from the package and remove all the cushioning. Remove the bubble wrap on the pipes while assembling the electronic drum rack. CAUTION The pipe ends may injure your fingers. Figure 3: Rack Assembly-1 *1 YAMAHA logo label on the curved pipe is facing the opposite side. *2 The knob is on the opposite side of the pipe. Figure 4: Rack Assembly-2 A B 2 See Figure 3. Set up the electronic drum rack, with the YAMAHA logo label (a) on the curved pipe facing the opposite side from you. Support the electronic drum rack with your left hand, and loosen the two knobs (b) and (c) on your right. 3 See Figure 4. Move the leg on your right (pipe ) in a counterclockwise direction until it is about 90 degrees from the curved pipe with the YAMAHA logo label. Tighten the two knobs loosened in step 2 and fix the position of pipe . 4 See Figure 3 again. Loosen the two knobs (d) and (e) on your left. The knob (d) is on the opposite side of the pipe. 5 See Figure 4 again. Move the leg on your left (pipe ) all the way around the standing vertical pipe in a counterclockwise direction until it is parallel with pipe . Tighten the two knobs loosened and fix the position of pipe . NOTICE Be sure to move pipe in a counterclockwise direction. If you move it in a clockwise direction, the slim pipes may collide and bend. * In the following steps, loosen the knobs first, decide the position of the pipe, and then tighten the knobs. Be careful not to tighten the knobs excessively. For better performance, make minor adjustments for each part of the unit with the knobs after the assembly is completed. Figure 5: Rack Assembly-3 6 See Figure 5. Loosen the three knobs of pipe , which are on the left bottom and opposite side from you (shown with ). Hold the area of pipe and shown with , and slide pipe so the further end of pipe will slide outward about 7 cm from the joint part with the standing vertical pipe. In the same manner, loosen the three knobs of pipe , which are on the right bottom and opposite side from you. Slide pipe so the further end of pipe will slide outward about 7 cm from the joint part with the standing vertical pipe. Tighten the six knobs loosened and fix the position of pipes and . 7 Insert the rubber foot on each further end of pipe and . Figure 6: Rack Assembly-4 H J C D E 8 See Figure 6. Loosen the two knobs ((h) on the upper left) aligned at the base of pipe , and move pipe slightly outward in a clockwise direction. Tighten the two knobs loosened and fix the position of pipe . 9 Loosen the two knobs ((j) on the middle right) aligned at the base of pipe and the knob ((k) on the lower right) of the slim pipe supporting pipe . Move pipe in a counterclockwise direction until it is about 90 degrees from the curved pipe with the YAMAHA logo label. Tighten the three knobs loosened and fix the position of pipe and the slim pipe supporting it. 10 Loosen the two knobs ((m) on the middle left) aligned at the base of pipe and the knob ((n) on the lower left) on the slim pipe supporting pipe , and move pipe in a clockwise direction until it is about 45 degrees from the curved pipe with the YAMAHA logo label. Tighten the three knobs loosened and fix the position of pipe and the slim pipe supporting it. NOTICE The pipes may bend when the area shown in collides. 11 Check that the entire electronic drum rack is stable. Hold the upper area of the vertical pipe and , and shake them. If the electronic drum rack is unstable, retighten the knobs tightened in steps 2 to 5. PRECAUTIONS Before using, please read this assembly manual, and use this product in a safe and proper manner. Particularly in the case of children and young users, parents or an instructor should teach the children the proper manner in which to use the device. WARNING If this symbol is ignored and the equipment is used improper...