Оценок - 1, средний балл: 4
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
These sections provide important information concerning the proper operation of the unit. Additionally, in order to feel assured that you have gained a good grasp of every feature provided by your new unit, Setup Guide 1, 2 and Owner’s manuals should be read in its entirety. These manuals should be saved and kept on hand as a convenient reference. Copyright © 2012 ROLAND CORPORATION All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION. 1 Percussion sound module and Pads Check the included items .. Hi-hat control pedal (FD-8) .. Kick pad .. Cymbal pad for hi-hat/ crush/ride (CY-5) . 3 .. Pad for snare/tom . 4 .. Percussion sound module (TD-4) .. Connection cable (special for TD-4KP) .. AC adaptor Manual set .. Setup Guide 1 (this document) .. Setup Guide 2 .. Owner’s Manual As soon as you open the package, check to see that all items are included. If anything is missing, please contact your dealer. * Use a commercially available kick pedal. 6 5 Attach the snare and toms Pipe and Mount positioning 1. Attach the snare and toms as shown in the illustration (four locations). Use the drum key to slightly loosen the pad bolts beforehand. MEMO • The snare and tom pads are all the same. • To mount tom 1 & 2, you will need to temporarily move the left or right pipe. • Mount the snare pad, making sure the bolt is on the opposite side of the player’s position. 2. Use the drum key to tighten the snare and tom bolts. 7 8 Attach the hi-hat Attach the cymbals 1. Remove the nut and attach the hi-hat pad as shown in the illustration. Pay attention to the direction of the rubber part attached to the tip of the hi-hat arm. 2. Tighten the not to obtain the desired amount of sway. 4 Extending the cymbal rods 1. Use the drum key to loosen the bolt of the movable section. 2. Tilt up the tips of the cymbal rods (two locations). 3. Release the lever at the top of the pipe, and pull out the cymbal rod. 9 Attach the kick pad 1. Rotate the kick pad and pedal plate holders as shown in the illustration. 1. Place the cymbals onto the tip of the cymbal rods (two locations). Align the cymbal with the narrow part of the cymbal rod, and insert the rod firmly. MEMO Place the cymbals onto the tip of the cymbal rods, and firmly press them to secure the position, as shown in the illustration. 3. Loosen the bolt and attach the pedal plate as shown in the illustration (do not tighten the bolt yet). 2. Attach the kick pad as shown in the illustration, and firmly tighten the kick pad attachment bolt. * Use a commercially available kick pedal. Anchor bolt Attach the anchor bolt (if installing on a drum mat) Anchor bolt Spring for the anchor bolt Release the lever and pull out the cymbal rod. Tilt up the cymbal rod. Use the drum key to loosen. 4. Tighten the lever to secure the rod. 1. Loosen the hand knobs and spread open the hit hat arm and sound module mount as shown in the illustration. Hi-hat control pedal Align with narrow part of cymbal rod, and insert firmly. Verify that the plate and pedal firmly contact the floor without any gap Pedal plate 3 Extend the pipes 1. Loosen the hand knobs at the locations shown, and extend the pipes. Adjust the pipes so that the stand is 85 cm (2’ 10”) high. Adjust the left and right tom pipes to the same height so that they face each other. * The pipes will come out if they are extended too far. NOTE 2. After you’ve extended the pipes, tighten the hand knobs to secure the pipes position. Left and right pipes facing each other 85 cm (2’ 10”) 2. Position the snare arm as shown in the illustration. 3. Loosen the knob and position the tom arm as shown in the illustration. 2 Open the stand 1. Loosen the hand knob and open the stand. Loosen Tighten Do not open wider than 90 degrees 2. Tighten the hand knob to secure the stand. 4. Kick pedal positioning. Mount the kick pedal to the pedal plate and so that the beater strikes the center of the kick pad. In order to this, you may have to loosen the knob on the kick pad to adjust the height and angle. Once the pedal is in the desired playing position, tighten the 2 knobs and bolt. Adjust the position of the beater so that it strikes the center of the kick pad striking surface, and firmly fasten the kick pedal and kick pad. Beater Kick pad Install the kick pedal securely. 3. Place the hi-hat control pedal below the hi-hat. Kick pad attachment bolt (included with the stand) With the OUTPUT jack facing out, use the drum key to securely tighten the bolt. * Take care not to pinch your fingers. NOTE * As shown in the illustration, do not open the stand wider than 90 degrees. If the stand is opened too wide, it will be less stable, and may fall over. NOTE Completed setup Crash Ride Hi hat Tom 1 Tom 2 Tom 3 Kick pad Snare Percussion sound module Hi hat control pedal Hit hat arm Tom arm Snare arm Sound module mount Loosen the bolt, then insert the pedal plate (don’t tighten the bolt). Nut Note direction S...