Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Only empty fuel tank in a well ventilated area and away from ignition sources. Remember butane is heavier than air. 2. Depress the filler valve at the back of the tank with a small bladed screwdriver and let the butane gas escape through the small orifice opening. It takes approximately one minute for the butane to escape from the tank. Be careful that the butane does not hit against your fingers or hands. This could cause frostbite of the skin. 3.One method is to poke a small bladed screwdriver through a piece of paper and then carefully depress the filler valve. The escaping gas will hit the paper and not your hand. 4. Never turn gas lever to “ON” and allow gas to evacuate through the ejector/tip. Doing this will clog the ejector and lead to premature failure. 5. Never try to unscrew the filler valve as it is adhesively bonded to the tank. Breaking of this bond will destroy the unit, causing the tank to leak. Specifications UT-100 UT-200 Overall length with soldering tip Overall length with heat tip Overall length as torch Weight (when gas filled) Approximate temp. soldering tip Approximate maximum temp. heat tip Approximate maximum temp. torch Gas Capacity Container Approximate operating time (one gas filling) 242mm (9.5 in.) 227mm (6.9 in.) 198mm (7.8 in.) 105g (3.7 oz.) 250° - 500°C (392° - 932°F) 700°C (1292°F) 1300°C (2372°F) 28ml (1.6 cu. in.) Max. 3 hours at #3 setting 286mm (11.3 in.) 268mm (10.5 in.) 235mm (9.3 in.) 220g (7.8 oz.) 300° - 530°C (572° - 986°F) 700°C (1292°F) 1300°C (23722°F) 63ml (3.8 cu. in.) Approx. 70 minutes at #3 setting 8 Optional Accessories UT-100 70-01-01 1mm dia. tapered needlesoldering tip 70-01-02 3.3mm dia. chisel soldering tip(standard) 70-01-03 2mm dia. spade soldering tip 70-01-04 3mm dia. spade soldering tip 70-01-05 0.5mm dia. tapered needle soldering tip 70-01-06 2mm dia. micro spade soldering tip 70-01-07 0.5mm dia. square tapered pyramid soldering tip 70-01-08 2mm dia. 35° spade soldering tip 70-01-09 3mm dia. 35° spade soldering tip 70-01-10 1mm dia. offset tapered needle soldering tip 70-01-11 8mm dia. high powered chisel soldering tip 70-01-12 3mm dia.. high powered round head needle soldering tip 70-01-13 5mm dia. high powered long tapered chisel soldering tip 70-01-15 7mm dia. 45° spade soldering tip 70-01-16 hot knife tip 70-01-50 2.5mm O.D./1.59mm I.D. 70-01-52 5.7mm O.D./4.9mm I.D. standard 70-01-51 4.25mm O.D./3.3mm I.D. 70-01-53 8.0mm O.D./7.4mm I.D. Outside Diameter Inside Diameter 70-01-55 heat shrink tip(standard) 70-01-54 heat shrink tip 70-52U carrying strap 70-02 protective cap 70-01-14 4mm dia. x 7mm pitchadaptor Soldering Tips Heat Tips 70-37U 70-40U Cleaner Pad Storage Box 9 Optional Accessories UT-200 Optional Accessories UT-200 72-01-07 1.5mm tapered pyramid soldering tip 72-01-14 soldering tip adaptor (5mm dia. x 0.8mm pitch) 72-01-01 3mm dia. tapered needled soldering tip 72-01-12 4mm dia. chisel soldering tip 72-01-02 10mm dia. chisel soldering tip (std.) 72-01-11 7mm dia. chisel soldering tip 72-01-03 4mm dia. spade soldering tip 72-01-13 12.5mm dia. spade soldering tip 72-01-05 1.5mm dia. tapered needle soldering tip 72-01-06 4mm dia. micro spade soldering tip 72-01-51 5.6 O.D./3.6 I.D. (mm) 72-01-52 8.8 O.D./6.6 I.D. (mm) 72-01-53 11.5 O.D./9.7 I.D. (mm) Std. 72-52U 72-01-54 (large) 72-01-55 (std) Heat Shrink Attachment Heat Tips Carrying Strap 72-02 Protective Cap Soldering Tips Outside diameter Inside diameter Ultratane™ Butane “ULTRA-REFINED” by Master…the only approved butane for Ultratorches. • Single piece universal tip • Purest refining method possible • Special non-clogging formula to permit extended use P/N 51773 - 5.125 oz. P/N 10448 - 26gm. canisters 10 Trouble Shooting Problem Probable cause Solution Does not ignite a. Empty tank b. Clogged ejector c. Fuel setting too high a. Refill with butane fuel b. Replace with new ejector c. Adjust switch ring or gas control lever to lower setting Low gas pressure Low flame a. Foreign object blocking tips b. Cold fuel a. Clean out or replace tips b. Hold unit in hand to allow unit to warmup. DO NOT HEAT HANDLE. Not enough heat a. Used-up catalyst b. Low fuel a. Replace with new tip b. Refill with butane gas Note: Ultratorches utilize the energy produced while evaporating butane gas. Ambient temperature affects operation. Adjust the unit as necessary. To Replace Ejector The ejector is where the air/fuel mixture takes place. Occasionally it may be necessary to replace due to clogging. Unscrew the knurled nut and remove the tip and tip housing. Push shutter lever upward to expose the small holes on the solder/heat ejector. Insert the accessory spanner wrench into one of the small holes and turn counter clockwise (CCW) until loose. (Continue to turn until easily removed.) Mount the new ejector in place of the removed ejector. Point the torch ejector downward and turn clock wise (CW), by hand, until tight. Use spanner wrench to tighten completely. Replace tip and tip housing. Storage of Yo...
Эта инструкция также подходит к моделям:Паяльные лампы - UT-100 (734.31 kb)