Войти:
Оценок - 1, средний балл: 3 ( )

Инструкция по эксплуатации Roland, модель TU-12

Производитель: Roland
Размер: 277.39 kb
Название файла:
Язык инструкции:en
Перейти к скачиванию



К этому устройству также есть другие инструкции:

Фрагмент инструкции


—' I ö Ö ó BOSS PSA-120, 220, 240 Amp. Electric guitar, bass guitar ф IW— Keyboard TU-12 INSTRUCTION MANUAL '88 MAR. B-' OPERATION [1] Chromatic Tuning OPERATION [2] Tuning Guitars or Bass Guitars o 0 P—GUI1AH OFF—. I f-CHROMATIC Q&D Set the MODE SELECT/POWER Switch to CHROMATIC. A = 440 Hz 445 Hz Select the pitch, pitch, A=440Hz Pitch") The TU-12 has the preset (Refer to "Selecting of Microphone Input Produce a (single) tone. a) If tuning the acoustic instrument, put it close to the Microphone. b) If tuning the electronic/electric instrument, connect it to the Input Jack by using a connecting cord. The indicator nearest to that tone will flash. -X-+J CHROMATIC C3 C3-IM-C3 C3 C3 C3 o CHROMATIC a a □ ca-M-a □ -fc • /tv‘ Now start tuning. (Example 1) If the Indicator under "E" lights as shown in the figure, it means the tone produced is near "E". (Example 2) If the Indicators under "G" and "#" light simultaneously, it means the tone near "G*" is produced. Tune it referring to mentioned later. FF—1 I rCHROMAI 1C OB ©-■■-a U3 a cn a a o A = 440 Hz 445 Hz 0°r<0 e -V-M- CDCDC3-«HE3 CD □ O Set the MODE SELECT/POWER Switch lo GUITAR. For guitars, the indicator of 6E (for the 6th string) will light. For bass guitars, the indicator of 4E (for the 4th string) will light. The symbols (i.e. 6E, 5A, 4D etc.) under the Indicators show the number of the string and its pitch. Select the pitch, pitch, A=440Hz. Pitch") The TU 12 has the preset (Refer to "Selecting of Select the number of the string to be tuned by pressing the UP (or DOWN) button. (Example) In case of the figure on the left, you can tune the 3rd string of a guitar and the 1st of bass guitar. a) If tuning the acoustic guitar, put its sound hole close to the Microphone. b) If tuning the electric guitar, connect it to the Input Jack by using a connecting cord. Tune it by producing a (single) tone. For tuning method, please refer to mentioned later. Selecting of Pitch I-ED a □ a a czi While you hold the Pitch button down, the Indicator will blink showing that the preset pitch is A=440Hz. PITCH DOWN o o UP ? Select the desired pitch by pressing the UP (or DOWN) button while the Pitch button is held down. The blinking of the Indicator will case when you release the Pitch button. However, the selected pitch will remain until the POWER Switch is turned off. How to check a tone with Meter and Tuning Guide 1. Chromatic Mode When a tone is produced, the Indicator shows the name of the tone (C~B ) and the Meter shows its pitch at the same time. (Example 1) Pitch A=440Hz just tuned (Example 2) Pitch A=443Hz lower just tuned higher % higher 2. GUITAR Mode Before tuning your guitar with this unit, tune it roughly by checkimi tension of the strings etc. (Example 1) PitchA=440Hz .rr-xV.:." i lower - rrr 1 - n . *J- N r-iJ t-i-J Li-* just tuned higher higher than quater tone (50 cent) (Example 2) PitchA=443Hz 1! . I . *1 uJ LC* just tuned Battery Replacement (9V x 1) If the indicator under B Starts flashing during operation, proper tuning function is no longer available. Please replace the battery with a new one. How to replace the battery 1 Remove the lid of the Battery Housing. 2 Take out the battery and separate it from the Battery Connector. 3 Place a new battery. (Be sure that the polarity is correct.) 4 Close the lid securely. Important • If the TU-12 is not to be used for a long time, remove the battery to prevent the trouble caused by battery leakage. AC Adaptor For AC operation, be sure to use the BOSS AC Adaptor PSA-120, 220 or 240 depending on the voltage system in your country, and never use one Adaptor for two units simultaneous- ly Note • If the B indicator starts flashing while the TU-12 is being operated with the AC Adaptor, tuning is not possible. If this happens, turn the TU-12 off, then turn it on again. • When an amplifier is connected to the TU-12, set the POWER switch of the TU-12 to OFF immediately after tuning is completed to avoid unnecessory consumption of the battery. Moreover, increasing the volume of the amplifier with the TU-12 on may cause noise. RADIO AND TELEVISION INTERFERENCE “Warning — This equipment has been verified to comply with the limits for a Class B computing device, pursuant to Subpart J, of Part 15, of FCC rules. Operation with non-certified or non-verified equipment is likely to result in interference to radio and TV reception." The equipment described in this manual generates and uses radio-frequency energy. If it is not installed and used properly, that is, in strict accordance with our instructions, it may cause interference with radio and television reception. This equipment has been tested and found to comply with the limits for a ...


Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории