Оценок - 4, средний балл: 5
(
)
)
|
Фрагмент инструкции
16) w=Velocity :01H - 7FH ( 1 - 127) mm.ll=Value of the parameter specified with RPN and/or NRPN * Ignored when "Rx.Note message = OFF". * In the drum pan, ignored when 'Rx.Note on = OFF” at each instrument. OVolume •Polyphonic key pressure Status BnH Second 07 H Third wH Status AnH Second kkH n=M!Dl channel number kk=Note number w=Value Third wH :OH - FH (ch.l - ch. 16) ООН • 7FH (0 • Î27) 00H-7FH (0- 127) Ignored when "Rx.Polyphonic key pressure = OFF". •Control change * All control change messages except channel mode messages are ignored when "Rx.Control change = OFF-. * The value set by control change messages won't be reset by receiving new Program Change messages. OBank select Status BnH BnH Second OOH 20H Third mmH 11H n=MIDI channel number w=Volume :()H-FH(ch.l - ch.16) :00H - 7FH (0- 127) The Volume value changes the volume of the specified channelfpam. Ignored when "Rx.Volumc = OFF". Ignored when "VOL RX : OFF". OPanpot Status BnH Second 0AH =M1D! channel number v=Panpot Third vvH :0H - FH (ch.l -ch.16) :00H • 40H - 7FH (Left - Center - Right) Resolution of panpot is approx. 7bit (127 steps). In drums pan. it works for all over the mapped drum instruments relatively. Ignored when 'Rx.Panpoi = OFF". OExpression n=MID! channel number mm.M=Bank number :0H - FH (ch.! - ch. 16) :00H.00H - 7FH.7FH (bank! - bank!6384} Status BnH Second 0BH Third wH The LSB 7bit is ignorcd(value=(X)H). "Bank seleci" is suspended until receiving "Program change". To select a timbre of another bank, you have to send Bank selcct(mm.ll) first and then send the Program change message. The "Variation number" of the DS-330 is defined as the decimal number of the value of MSB(Control change number OOH) of the Bank select. Ignored when "Rx.Program Change * OFF'. Ignored when “PRC RX: Off'. n=MIDl channel number w=Exprcssion :0H - FH (ch.l • ch. 16) :(X)H - 7FH (0 - 127) The Expression value changes the volume of the specified channelipart). Ignored when "Rx.Expression = OFF'. 94 OHoidl Status BnH Second 40H Third wH n=MIDl channel number :0H - FH (ch. i - ch. 16) w=Contro! Value KWH - 7FH (0 - 127) 0-63=OFF 64-l27=ON * Ignored when "Rx.Holdl * OFF'. * Ignored when "HOLD1 : OFF'. OPortamento Status Second BnH 41H Third wH n=M!Dl channel number :QH * FH (ch. I • ch. 16) w=Control Value :OOH - 7FH (0 - 127)0=OFF • Ignored when “Rx.Portamento = OFF'. OSostenuto ••NRPN** NRPN (Non Registered Parameter Number) is an expanded control change message. Each function of an NRPN is described by the individual manufactures. Set NRPN MSB/LSB before sending data entry. You can change the value of several sound parameters. There are relative change(from preset) parameters and absolute change parameters. The relative change parameters may have limits on the effect (depend upon the timbres) even if the value is between OEH-72H. The NRPN parameters of the DS-330 are as shown below; NRPN Data entry MSB LSB MSB 01H0AH Description Vibrate rate relative change on specified channel mm: 0EH-40H-72H (-50 • 0 - +50) Vibrate depth relative change on specified channel mm: 0EH-40H-72H (-50 - 0 - +50) Vibrate delay relative change on specified channel mm: OEH^OH-72H (-50 • 0 - +50) Status BnH Third wH n=MlDI channel number :0H - FH (ch.l -ch.16) wsControl Value ()-63=OFF 64-127=ON :00H - 7FH (0 * 127) * Ignored when "Rx.Sostenuto = OFF. OSoft TVF cutoff frequency relative change on specified channel mm: 0EH-40H-72H (-50 - 0 - +50) TVF resonance relative change on specified channel mm: OEH^OH-72H (-50 - 0 - +50) TVF&TVA Env. Attack time relative change on specified channel mm: 0EH-40H-72H (-50 - 0 - +50) Status BnH Second Third 43H wH n=MIDl channel number :0H-FH(ch.l -ch.16) w=Control Value ()-63=OFF 64-127=ON :00H - 7FH (0 • 127) Ignored when "Rx.Soft = OFF". OEffectl depth(Reverb send level) Status Second Third BnH 5BH wH n=MlDI channcl number :0H-FH(ch.l -ch.16) vvsReverb send depth :00H - 7FH (0 - 127) * You can adjust the reverb send level of a specified channcl(part). OEffect3 depth(Chorus send level) Status BnH Third wH n=M!Dl channel number :0H - FH (ch.l -ch.16) w=Chorus send depth :00H-7FH(0- 127) * You can adjust the chorus send level of a specified channel(part). mmH TVF&TVA Env. Decay time relative change on specified channel mm: 0EH-40H-72H (-50 - 0 - +50) mmH TVF&TVA Env. Release time relative change on specified channcl mm: 0EH-4OH-72H (-50 - 0 - +50) mmH Pilch coarse of drum instrument relative change on specified drum instrument rr: key number of drum instrument mm: 00H-40H-7FH (-64 - 0 - +63 semitone) mmH TVA level of drum instrument absolute change on specified drum instrument nr: key number of drum instrument mm: 00H-7FH (zero - maximum) mmH Panpot of drum instrument absolute change on specified drum instrument it: key number of drum instrument .. mm: 00H.0IH-40H-7FH (Random. Left-Cente...