Оценок - 5, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
If this happens, use connection cables that do not contain resistors. RING RINGTIP TIP Portugues Italiano DeutschNederlands Espanol Francais English Switching the Power On and Off Once the connections have been completed, turn on power to your various devices in the order specified. By turning on devices in the wrong order, you risk causing malfunction and/or damage to speakers and other devices. 1. Make sure that all [VOLUME] knobs on the CUBE-20XL BASS and all the connected devices are set to 0. 4. Adjust the volume levels for the devices. 5. Before switching off the power, lower the volume on each of the devices in your system and then TURN OFF the devices in the reverse order to which they were switched on. * If you need to turn off the power completely, first turn off the [POWER] switch, then unplug the power cord from the power outlet. Refer to “Power Supply” (p. 3). 2. Turn on all the devices connected to the CUBE-20XL BASS’s input jacks (BASS INPUT jack and AUX IN jack). 3. Turn on the CUBE-20XL BASS. * Always make sure to have the volume level turned down before switching on power. Even with the volume all the way down, you may still hear some sound when the power is switched on, but this is normal, and does not indicate a malfunction. * This unit is equipped with a protection circuit. A brief interval (a few seconds) after power up is required before the unit will operate normally. 7 Using the Tuner Function Chromatic Tuning If you press the [TUNER] switch for one full second or more, the [TUNER] switch flashes and the unit becomes usable as a “chromatic tuner,” which automatically determines the name of the note closest to the one played. 1. Press and hold the [TUNER] switch for at least one second. [TUNER] switch flashes and CUBE-20XL BASS enters the chromatic tuner mode. 2. Play a single note on the open string that you want to tune. Tune the string until the green indicator lights. Manual Tuning Use manual tuning when the strings are substantially out of tune (such as after changing strings). 1. Press the [TUNER] switch. CUBE-20XL BASS enters the Tuner mode and the [TUNER] switch lights up. 2. Use the Type switch to select the string that you want to tune. CUBE-20XL BASS is equipped with a tuner function. In addition to manual tuning, you can also use it as a chromatic tuner. * Once in the Tuner mode, no sound is played from the speaker or the REC OUT/PHONES jack. * The sound input to the AUX IN jack is output. Knob Position Description 5B Open fifth string (B) 4E Open fourth string (E) 3A Open third string (A) 2D Open second string (D) 1G Open first string (G) A Open third string (semitone down) (A ) * The reference pitch is A=440 Hz. This cannot be changed. 3. Play a single note on the open string that you want to tune. Tune the string until the green indicator lights. Flat Sharp Pitch is correct Lights red Lights green Lights red * The red indicator flashes if the pitch is substantially out of tune. 4. When you have finished tuning, press the [TUNER] switch once again. 9 Nederlands Portugues Espanol Italiano Francais Deutsch English ALL ROUND (SUPER FLAT) An original amp featuring a wide-range frequency response. This amp type enables clear reproduction of your instrument’s sound. This also makes it perfect when connecting bass modeling processors or using sound modules like bass synth. In addition, you can exploit the equalizer’s capabilities to create the perfect bass sound for any musical genre from rock to jazz When POLY OCTAVE is turned on, the entire range of sound, from bass to treble, will become much more robust. SLAP BASS (SESSION) This setting cuts the midrange for a great slap bass sound. Setting the SHAPE switch to ON further boosts the low and high ends. To get a crisp slap sound, lower the MIDDLE setting and raise the TREBLE. This emphasizes the brightness of the string sound, resulting in a slap sound with a lighter pull sound. By applying COMP, you can greatly enhance the clarity of the sound. To get that attacking sound used in rock music, raise the BASS and MIDDLE settings to produce a sound with greater power. FINGER & FRETLESS (BASS 360) This bass sound made its appearance in the ’70s. This is suited for a Jazz Bass with a rear pickup used. This produces a warm, contoured sound when the bass is fingered near the rear pickup. In addition, using this setting while playing harmonics in combination with a chorus and a delay enables sounds featuring exquisite reverberation. ROCK RIFF (CONCERT 810) This is a fat, powerful standard bass sound. Raise the MIDDLE setting to produce a clear picking sound when the bass is picked. If you want a fatter low end, set the SHAPE switch to ON. Raising the DRIVE results in an even fatter distortion sound. [SHAPE] Switch: OFF [SHAPE] Switch: ON or OFF [SHAPE] Switch: OFF [SHAPE] Switch: ON or OFF Sample Settings 10 Setting Memo [SHAPE] Switch: [SHAPE] Switch: [SHAPE] Switch: [SHAPE] Switch: Specifications CUBE-20XL BASS (CB-20XL) Rated Powe...