Оценок - 0, средний балл: 4
(
)
)
|
Фрагмент инструкции
Channel 2 7. Mic Input XLR Unbalanced low impedance for microphone input. 8. Left / Mono Jack This is for either a mono input or the left side of stereo input if item 9 is used as well. This is a high impedance unbalanced input. Typical uses of Line Inputs are Keyboards, drum machines and sequencers. 9. Right Jack For use with the right side of a stereo input when used in conjunction with item 8. This is a high impedance unbalanced input. 10. Volume Controls individual volume level for channel 2. Overall volume will be governed by the Master Volume control (item 20). 11. Effect & Reverb When using the in-built reverb on the LR230 this control will adjust the amount of reverb on Channel 2. When using an external effects processor this will control the amount of effected signal through Channel 2, as it dictates the amount of signal to the Effects Send (item 12). Note - this will be effected by the Effect Return control (item 15) and the Master Reverb control (item 16). Effects The LR230 features a parallel effects loop to allow you to use external effects processors. 12. Send Jack For connection processor (mixed 13. Return Left / Mono For connection to the left external effects processor or mono effects processor. 14. Return Right Jack For connection to the right output of a external effects processor. 15. Effect Controls the ratio of effected to dry signal in your overall tone. Further control is given by Effect & Reverb controls on Channel 1 and Channel 2 (item 5 and item 10). Reverb 16. Reverb Controls master level of internal reverb. 17. Remote Jack Allows you to switch internal reverb on and off from remote footswitch (optional extra, model no. PEDL-00020) Master 18. Low Controls overall low frequencies of combo. 19. High Controls overall high frequencies of combo. 20. Volume Controls overall volume of combo. This also controls the level of the Line Out on the rear panel. 21. Power Switch Switches the mains power to the combo and indicates power status. LR230 Rear Panel Features (page 36) 1. Mains Input For connection to the mains. We would always recommend that your plug is wired in accordance with your country’s regulations. 2. Headphone Jack For headphone input when silent practice is the call of the day. Note - connecting headphones will disconnect internal speakers. Line Out In some instances you will want to connect the LR230 to a P.A. system or to recording equipment. The Line Out level on the LR230 is controlled by the Master Volume (item 20). 3. Left For connecting the left hand signal to a P.A. system or recording equipment. 4. Right For connecting the right hand signal to a P.A. system or recording equipment 4 AUDIOSTATE AUDIOSTATE LR150 LR150 Top Panel Channel 1 & Channel 1. & 5. Low Controls the low frequencies on Channel Channel 2 respectively. 2. & 6. High Controls the high frequencies on Channel 1 and Channel 2 respectively. 3. & 7. Effect When using the in-built reverb on the LR150 this control will adjust the amount of reverb on Channel 1 and Channel 2 respectively. When using an external effects processor this will control the amount of effected signal, as it dictates the amount of signal to the Effects Send (item 10) on the rear panel. Note - this will be effected by the Effect Return control (item 19) and the Master Reverb control (item 20). 4. & 8.Volume Controls individual volume level for channel 1 and 2 respectively. Overall volume will be governed by the Master Volume control (item 21). Channel 3 & Channel 4 9. & 14. Low Controls the low frequencies on Channel 3 and Channel 4 respectively. 10. & 15. Mid Controls the mid frequencies on Channel 3 and Channel 4 respectively. 11. & 16. High Controls the high frequencies on Channel 3 and Channel 4 respectively. 12. & 17. Effect When using the in-built reverb on the LR150 this control will adjust the amount of reverb on Channel 3 and Channel 4 respectively. When using an external effects processor this control will control the amount of effected signal, as it dictates the amount of signal to the Effects Send (item 10) on the rear panel. Note - this will be effected by control (item 19) and the Master (item 20). 13. & 18. Volume Controls individual volume level for channel and 4 respectively. Overall volume will be governed by the Master Volume control (item 21). Master Section 19. Effect Return This is the master Effects Return and is an effects mix control, allowing you to decide when using an external effects processor how much of your overall sound will be effected. Further control is given by the individual Effect control which features on each channel. 20. Master Reverb The LR150 comes complete with an in-built spring reverb. The overall reverb level for the combo is set here, with independent controls featuring on each channel allowing you to set independent levels for each channel. 21. Master Volume The overall volume of the combo is set here. As with effects and reverb, there is an independent control on each channel allowing ...
Эта инструкция также подходит к моделям:Музыкальные инструменты - AUDIOSTATE LR150 (798.23 kb)
Музыкальные инструменты - AUDIOSTATE LR230 (798.23 kb)