Оценок - 6, средний балл: 4
(
)
)
|
Фрагмент инструкции
This setting is switched in pairs: AUX 3/4 and 5/6. When the switch is pressed in, the pre-fader signal will be sent to the corresponding pair of AUX buses. When the switch is in the out (up) position, the post-fader signal will be sent. 8PAN control This adjusts the left/right position at which the input channel signal will be sent to the ST (stereo) bus, GROUP bus 1/2, and GROUP bus 3/4. 9ON switch This switches the input channel on/off. When this switch is turned off, the signal of the input channel will not be sent to the ST bus, GROUP buses, or AUX buses. However even if this switch is off, you can use the PFL switch (B) to monitor the signal from the C-R OUT jacks or the PHONES jack. 0Group select switches These switches send the signal of the input channel to GROUP buses 1–4. When the 1–2 switch is on (pressed in) the signal will be sent to GROUP bus 1/2. When the 3–4 switch is on, the signal will be sent to GROUP bus 3/4. AST (stereo) switch This switch sends the signal of the input channel to the ST bus. When this switch is on, the signal will be sent to the ST bus. BPFL (pre-fader listen) switch This switch sends the pre-fader signal to the PFL/ AFL bus, allowing you to monitor it through headphones or monitor speakers. When this switch is on, the pre-fader signal of the input channel can be heard from the C-R OUT jacks and the PHONES jack, even if the ON switch (9) is off. CChannel fader This fader adjusts the input level of the input channel. The position of the channel fader will affect the level of the signal that is output from the ST bus, GROUP buses 1–4, and AUX buses 1– 6 (except when the PRE switch is on for AUX buses 3–6). PHANTOM INPUT A 1-20 {1-12} {1-8} INPUT B PFL ST ON 3-4 1-2 PFL/AFL LR AUX 654321 GROUP AUX 6 AUX 5 AUX 4 AUX 3 PRE AUX 2 AUX 1 PAN PEAK 0dB+48V 80 gg LOW fg MIDHIGH 3 Stage EQ ST RL PRE INSERT I/O HPF PHANTOM +48V 26dB PAD 4321 HA GAIN Mono input channel signal flow —Owner’s Manual Front and rear panel Front and rear panel PEAK HIGH 4 6 Stereo input channels Here are the two stereo input channels provided by the GF24/12, GF16/12, and GF12/12. The 1 INPUT 21/22 and 23/24 {13/14 and 15/16 on the 2 GF16, and 9/10 and 11/12 on the GF12/12} jacks (6and 0 of the connector section) are pairs of 3 connectors that let you control a stereo signal using one input channel. If a cable is connected only to the INPUT A 21L or 23L jack {13L or 15L on the GF16/12, or 9L or 11L on the GF12/12}, the source will be controlled as a monaural signal. 5 1A/B switch This switch selects input jacks. When the switch is in the upward position ( ) the input signal of the INPUT A jack is selected (page 18, 6 of the connector section). When the switch is in the downward section ( ), the input signal of the INPUT B jack is selected (0 of the connector section). 2GAIN control This adjusts the input sensitivity. The range of levels that can be accommodated is +10 dB to –34 dB. 3High pass filter switch This is an on/off switch for the high pass filter 7 that cuts the frequency range below 80 Hz at a slope of 12 dB/octave. The high pass filter is on when the switch is pressed in. 4PEAK indicator This is an indicator that detects post-EQ clipping. 8 It will light 3 dB before clipping, indicating that the signal is near the clipping level. If this LED 9 lights, lower the GAIN control (2). 5EQ controls (HIGH/MID/LOW) This is a three-band equalizer that boosts/cuts 0 each frequency band over a ±15 dB range. The center frequency and equalizer type for each band is shown below. A B C Band Center frequency Type HIGH 10 kHz shelving MID 250 Hz peaking LOW 100 Hz shelving The response is flat when the knob is in the “” position. —Owner’s Manual A B +10 –34 –15 +15 80 MID –15 +15 PFL 1–2 ON 3–4 ST 10 5 0 5 10 15 20 30 40 BAL R EVEN L ODD PRE PRE 1 2 3 4 5 6 0 10 0 10 0 10 0 10 0 10 0 10 LOW AUX PRE –15 +15 Channel controls Channel controls 7PRE switches These switches select whether the pre or post fader signal will be sent to AUX buses 3–6. This setting is switched in pairs: AUX 3/4 and 5/6. When the switch is pressed in, the pre-fader signal will be sent to the corresponding pair of AUX buses. When the switch is in the upward position, the post-fader signal will be sent. 8BAL (balance) control This adjusts the left/right balance at which the signal of the stereo input channel will be sent to the ST (stereo) bus, GROUP bus 1/2, and GROUP bus 3/4. 9ON switch This switches the input channel on/off. When this switch is turned off, the signal of the input channel will not be sent to the ST bus, GROUP buses, or AUX buses. However even if this switch is off, you can use the PFL switch (B) to monitor the signal from the C-R OUT jacks or the PHONES jack. 0Group select switches These switches send the signal of the input channel to GROUP buses 1–4. When the 1–2 switch is on (pressed in) the signal will be sent to GROUP bus 1/2. When the 3–4 switch is on, the signal will be sent to GROUP bus 3/4. AST (stereo) switch This...
Эта инструкция также подходит к моделям:Музыкальные инструменты - GF12/12 (602.37 kb)
Музыкальные инструменты - GF24/12 (602.37 kb)