Оценок - 4, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
..• Power on/off muting. ..• Long-lasting crossfader. MIXER CONTENTS .................................. 1. Input fader - Controls individual source levels (channels) in the mix. 2. Input toggle switch - Selects which source will be active based on what you have connected to the rear panel input section (phono/line). 3. Channel EQ - Adjusts the high, mid and low frequency levels of the input channels for good sound. 4. Channel Gain – Adjusts the pre-fader volume for cleaner sound. 5. Replaceable Crossfader - Achieves clean segues between the two input channels. "Hard left" selects Channel 1. "Hard right" selects Channel 2. With the crossfader centered, both channels are live. Use the crossfader for fast and seamless segues (fades) from one channel to the other. Note: The crossfader is user replaceable in case of failure. Simply unscrew the two large screws which hold it in place, lift it out and disconnect its cable. Re-attach the new crossfader and screw the mounting plate back onto the unit - you’re back in business! 6. Mic Input Gain – Adjusts microphone input level. 7. Mic Input – Insert your Microphone with .” plug here. 8. Headphone Input – Insert in the .” plug for your headphones here. 9. Channel Cue / Cue Pan - Used to preview channel audio to your headphones. Listen here before bringing up channel faders or moving the crossfader. 10.Headphone Level – Adjusts cue volume. 11.Master Level - Controls the overall output level. 12.Level Indicators – The dual LEDs indicators are used to indicate the master output level of channels Right and Left. 13.Mic EQ – The mic channel include a two-band EQ with a range of +10dB to –10dB. MIXER CONTENTS 14. Grounding post - for turntable connection. Always use this connection when using standard turntables with ground cable. (Some turntables like the T.80 / T.120 do not require grounding wire). 15. Phono Inputs – Plug your turntables in here. When these connectors are used, your signal is fed directly to the high-quality RIAA phono pre-amplifiers. Use this position only for turntables. Line level sources will overload the sensitive phono pre-amps and will cause distortion. 16. Line Inputs - Unbalanced RCA jacks for connecting stereo audio from line level sources such as CD players, HiFi VCRs, cassette decks, DAT machines, laser discs, tuners, even synthesizers or other mixing consoles. NOTE: Plug mono audio sources into both Left and Right inputs using a "Y" cable connector. 17. Master Output - Unbalanced RCA connectors controlled by the Master level. 18. Power Switch – turns unit off and on. Note*** Remember to turn ALL volume levels down when turning on/off the unit. 19. Power Connector - Plug in the included power supply here. .... .... .... .... .... .... QUICK SETUP DIAGRAM Study this setup diagram. Make sure all faders are at "zero" and all devices are off. First, connect all input sources and processors. Next, connect your microphone and monitor headphones. Finally, connect the stereo outputs to the power amplifier(s) and/or audio receivers such as tape decks. Plug your mixer into AC power. Now you are ready to switch everything on. IMPORTANT: Always switch on your audio input sources such as turntables or CD players first, then your mixer, and finally any amplifiers. When turning off, always reverse this operation by turning off amplifiers, then your mixer, and then input devices. .................. .................. ........................ .................. .................. ............ ............ SPECIFICATIONS INPUT / OUTPUT IMPEDANCE & SENSITIVITY: LINE -14dB/10K OHM ±2dB PHONO -50dB /47K OHM ±2dB MIC -60dB /2.2K OHM ±2dB MASTER 1K OHM PHONES 0dB/33 OHM ±2dB (LOAD=32 OHM) MAX. OUTPUT (THD=1%) MASTER MORE THAN +14dBV PHONES MORE THAN +21dBV CHANNEL BALANCE WITHIN 3dB FREQUENCY RESPONSE: LINE 20-20KHz ±2dB PHONO 20-20KHz +2, -3dB (RIAA) MIC 20-20KHz +2/-3dB OUTPUT NOISE (IEC-A WEIGHTED) LINE LESS THAN -90dBV PHONO LESS THAN -80dBV MIC LESS THAN -50dBV THD + N: (MASTER 0dBV OUTPUT, MAXIMUM GAIN, w/ 20kHz LPF) LINE LESS THAN 0.05% 20 - 20KHz PHONO LESS THAN 0.1% 20 - 20KHz (IEC-A WTD) MIC LESS THAN 0.2% 20 - 20KHz (IEC-A WTD) PHONES LESS THAN 0.1% 20 - 20KHz (FROM LINE INPUT) CROSSTALK LESS THAN -80dB AT 1KHz BETWEEN CHANNELS. (TERMINATED UNUSED INPUTS) MIC EQ HI ±10 +/- 2dB AT 10KHz LOW ±10 +/- 2dB AT 100Hz CHANNEL EQ HI 9 +/- 2dB AT 13KHz -15 +/- 3dB AT 13KHz MID 9 +/- 2dB AT 1KHz LESS THAN -23dB AT 1KHz LOW 9 +/- 2dB AT 70Hz -26 +/- 3dB AT 70Hz POWER SOURCE AC 9V,1000mA DIMENSIONS 230 (W) X 267 (D) X 111 (H) mm WEIGHT 1.61Kgs Stanton Magnetics, Inc. – Warranty Provision – Returns for Repairs or Replacement WARRANTY Through Stanton’s authorized dealers around the World, Stanton, or one of Stanton’s authorized distributors outside the U.S., will, without charge, repair or replace, at the sole discretion of the entity responsible for making the repair or providing the replacement, any Stanton merchandise proved defective in material or workmanship for ...