Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
This will ensure long life and keep a smooth feeling throughout the fader's lifetime. Follow the instructions below to lubricate and clean your faders: REMOVING A FADER: 1. Make sure mixer is powered off and power supply is disconnected from the back of the mixer. 2. To remove the lower faceplate, take off all the fader knobs and then remove the 4 screws located on the sides of the mixer (2 on each side). Lift up on the faceplate and it will slide off. 3. Remove the fader to be cleaned or replaced by unscrewing the 2 outer screws on the fader plate (removing the 2 inner screws will detach the fader from the fader plate). 4. Disconnect the fader from the mixer by removing the connector on the bottom of the fader. CLEANING A P&G FADER: 1. Remove 2 mounting screws from fader plate. (NOTE: The P&G fader is designed with floating mounting threads for precise mechanical centralizing of the fader. If you desire to keep your fader`s current mounting position we suggest that you make 2 marks on both ends of the fader on the fader plate to indicate the P&G fader position.) See Figure 1. 2. Once fader is removed from the unit, remove the two screws (A) from the end of the fader body where the wires exit the fader casing. Pull away the end block. Withdraw the dust cover (B). Taking great care, remove the slider assembly (C), ensuring that the wiper contacts (D) are not damaged as this will affect the operation of the fader. Clean the slider assembly by gently wiping the wiper contacts and slider bearings (E) using a tissue or cotton bud. If the slider bearings are excessively worn, as indicated by excessive slider rocking, then contact Stanton for replacement. 3. Remove the single upper screw on the opposite end block to remove the guide rail. Clean the guide rail (F) with a tissue or cloth, removing all traces of dirt and contamination. 4. Remove the fader track (G) by slowly withdrawing from the unit. Place the fader track on a desk or working surface with black contacts facing upwards. If necessary, the track can be washed in warm water, wiped gently then dried thoroughly using a dry cloth. Use a lint free cloth or swab to wipe the tracks and check for marks along the track. (Note: Lint free cloth should be used to avoid dust and fibers being deposited on the track). If the track appears excessively worn, or if cleaning does not improve its operation, replacement may be necessary. A B C D E F G Figure 1 FADER CLEANING AND REPLACEMENT FADER CLEANING AND REPLACEMENT 5. Examine the center channel of the fader body (found inside the bottom of the fader casing) and if dirty, clean using cotton buds. 6. Re-assemble and lubricate the fader as follows: a) Secure the end block and guide rail onto the fader body. b) Insert track into the fader body. c) Insert slider assembly onto guide rail and into the fader body. Move slider from end to end to disperse the oil evenly. Carefully wipe away any excess oil using a tissue or cloth. d) Lubricate the guide rail by placing one drop of silicon liquid oil onto the guide rail (F). e) Insert dust cover. f) Insert fader track back into fader body with wires coming out open end of fader body. g) Secure the remaining end block ensuring that the track wires (I) are not pinched between the end block and fader casing. 7. Once assembled, move the slider from end to end to ensure operation is smooth. 8. Attach fader to fader plate. (NOTE: As noted earlier if you do not want to change positioning of fader, keep the 2 fader plate screws loose and shift the fader until it is aligned with the marks you created in step 1, then tighten fader plate screws.) REPLACING THE FADER: 1. Once the fader has been removed, simply plug the connector into the new fader. 2. Place fader back in mixer and replace 2 outer screws to secure fader. ROTATING THE OS2 SWITCHES The optical scratch switches (OS2) on the Stanton SA.5 mixer can be rotated to 8 different positions. Follow the steps below to rotate the OS2 to the position you like: 1. Make sure the mixer is powered off. Remove the faceplate of the mixer. 2. Remove the two outer screws from the OS2 as indicated in diagram. Do not remove the two inner screws. Removing the two inner screws will detach the OS2 from its plate. 3. Rotate the OS2 to the position you like. Replace the two outer screws to secure the OS2 in place. REPLACING THE OS2: 1. Follow steps 1 and 2 above. Remove switch from mixer and detach the connector from switch. 2. Attach the connector for OS2 to the replacement switch and replace two outer screws to secure the OS2 in place. TECHNICAL SPECIFICATIONS TECHNICAL SPECIFICATIONS Line input: 2 (RCA) x 2 channels, -10 dBV / 10 kOhm Session Input: 2 (RCA), -10 dBV / 10 kOhm Phono input: 2 (RCA) x 2 channels, -50 dBV / 47 kOhm Mic input: 1(1/4") -50 dBV / 2.4 kOhm balanced Master output: 2 (1/4”) Balanced / 2 (RCA) unbalanced, +4 dBu balanced / -10 dBV unbalanced Record output: 2 (RCA), -10 dBV / < 100 Ohms Headphone output: 2 (1/4 inch), 1 (1/8 inch...