Войти:
Оценок - 4, средний балл: 3.5 ( )

Инструкция по эксплуатации Makita, модель HR2021

Производитель: Makita
Размер: 538.1 kb
Название файла:
Язык инструкции:svitenesfrdenlptdafi
Перейти к скачиванию



Фрагмент инструкции


SAVE THESE INSTRUCTIONS. OPERATING INSTRUCTIONS Side grip (auxiliary handle) (Fig. 1) Always use the side grip to ensure operating safety. Install the side girp so that the teeth on the grip fit in between the protrusions on the tool barrel. Then tighten the grip by turning clockwise at the desired position. It may be swung 360° so as to be secured at any position. Installing or removing the bit Installing or removing the bit : Always be sure that the tool is switched off and unplugged before installing or removing the bit. Clean the bit shank and apply bit grease before installing the bit. (Fig. 2) Insert the bit into the tool. Turn the bit and push it in until it engages. (Fig. 3) After installing, always make sure that the bit is securely held in place by trying to pull it out. To remove the bit, pull the chuck cover down all the way and pull the bit out. (Fig. 4) Depth gauge (Fig. 5) The depth gauge is convenient for drilling holes of uniform depth. Loosen the side grip and insert the depth guage into the hole in the side grip. Adjust the depth gauge to the desired depth and tighten the side grip. NOTE: The depth gauge cannot be used at the position where the depth gauge strikes against the gear housing. Switch action (Fig. 6) CAUTION: Before plugging in the tool, always check to see that the switch trigger actuates properly and returns to the “OFF” position when released. For Model HR2020, HR2020X and HR2021 To start the tool, simply pull the switch trigger. Tool speed is increased by increasing pressure on the switch trigger. Release the switch trigger to stop. For continuous operation, pull the switch trigger and then push in the lock button. To stop the tool from the locked position, pull the switch trigger fully, then release it. For Model HR2022 To start the tool, simply pull the switch trigger. Release the switch trigger to stop. For continuous operation, pull the switch trigger and then push in the lock button. To stop the tool from the locked position, pull the switch trigger fully, then release it. Reversing switch action (Fig. 7) For Model HR2020 and HR2020X This tool has a reversing switch to change the direction of rotation. Move the reversing switch lever to the A side for clockwise rotation or the B side for counterclockwise rotation. CAUTION: • Always check the direction of rotation before operation. • Use the reversing switch only after the tool comes to a complete stop. Changing the direction of rotation before the tool stops may damage the tool. • When you operate the tool in counterclockwise rotation, the switch trigger is pulled only halfway and the tool runs at half speed. For counterclockwise rotation, you cannot push in the lock button. Selection action mode (Fig. 8) This tool employs an action mode changing knob. Select one of the two modes suitable for your work needs by using this knob. For rotation only, turn the knob so that the arrow on the knob points toward the M symbol on the tool body. For rotation with hammering, turn the knob so that the arrow on the knob points toward the r symbol on the tool body. CAUTION: • Always set the knob fully to your desired mode symbol. If you operate the tool with the knob positioned halfway between the mode symbols, the tool may be damaged. • Use the knob after the tool comes to a complete stop. Torque limiter The torque limiter will actuate when a certain torque level is reached. The motor will disengage from the output shaft. When this happens, the bit will stop turning. CAUTION: • As soon as the torque limiter actuates, switch off the tool immediately. This will help prevent premature wear of the tool. • Hole saws cannot be used with this tool. They tend to pinch or catch easily in the hole. This will cause the torque limiter to actuate too frequently....

Эта инструкция также подходит к моделям:
Прочие инструменты - HR2020 (538.1 kb)
Прочие инструменты - HR2022 (538.1 kb)
Прочие инструменты - HR2020X (538.1 kb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории