Оценок - 4, средний балл: 3.5
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION. Before using this unit, carefully read the sections entitled: "USING THE UNIT SAFELY" and "IMPORTANT NOTES." These sections provide important information concerning the proper operation of the unit. Additionally, in order to feel assured that you have gained a good grasp of every feature provided by your new unit, Owner's manual should be read in its entirety. The manual should be saved and kept on hand as a convenient reference. Check the included items Stand (MDS-4) The parts required to assemble the stand (MDS-4) are listed in the MDS-4 Owner's Manual. Check the owner's manual and make sure that you have all of the parts. As soon as you open the package, check to see that all items are included. If anything is missing, please contact your dealer. TD-4K parts V_ □ Hi-hat control pedal (FD-8) □ Kick trigger pad (KD-8) □ Cymbal pad for hi-hat (CY-5) □ Cymbal pad for crash/ride (CY-8 x 2) □ V-Pad for snare (PDX-8) □ Pad for tom (PD-8 x 3) □ Drum sound module (TD-4) □ Connection cable (special for TD-4) Manual set □ Setup Guide (this document) □ Owner's Manual □ Drum key Assemble the stand r Assembly procedure ^ Assemble the stand using the procedure described in the MDS-4 Owner's Manual. J Cymbal mounts Hi-hat mount If the stand wobbles, loosen this hand knob and adjust the height. For reasons of safety, do not spread the stand wider than 1.0 meters (40 inches). 1.0 m (40") Attach the parts * The parts required for mounting the cymbals and the hi-hat are included in the TD-4K attachment box. Attach the hi-hat (CY-5) Attach the crash cymbal (CY-8) and ride cymbal (CY-8) Tighten the bolt with a drum key. Rotation stopper [#7\Y (note orientation) Attach the bolt so that it is at the right when seen by the performer. Tighten the wing nut to obtain an appropriate amount of sway. Assemble the hi-hat control pedal (FD-8) Assemble the kick (KD-8) Attach the anchor bolt (if installing on a drum mat) ^ -Anchor bolt Anchor bolt C \ Adjusting the pedal depth Loosen with the drum key, and tighten after adjusting ^ Spring for the anchor bolt k Deeper Slide >h' arm^^^^=55::5..,,^^ " Shallower J Remove the stand fastening screws from the reverse side of the KD-8's trigger. Pull out the stand in the direction of the arrow, and use the screws you removed earlier to fasten the stand. Attach the sound module (TD-4) The wingnut screws needed for accomplishing the installation using the sound module mounting plate were packed inside the bag containing the AC adaptor. Attach the snare (PDX-8) and toms (PD-8) Tighten Tighten Loosen Adjusting the tension (PDX-8) 6^—--1 4 3 2 ------^5 1. Finger-tighten all six of the tuning bolts in the sequence shown in the illustration. 2. The appropriate amount of tension is one that will provide approximately the same striking response as on an acoustic drum. 3. Use the drum key to adjust the tension as needed. r Connect the pads to the sound module Connection procedure 1. Connect the cable to the TD-4 as shown in the illustration. Labels indicating the pad to be connected are attached to the cable. Connect the cable to the OUTPUT jack of each pad as shown in the illustration. * Use cable ties to fasten the cables at the circled locations " " so that they do not interfere with your performance. Make sure to wrap the cable ties around the pipes. Do not connect the CR2 cable (for extension). Leave the cap in place, and fasten the cable so that it will not hinder your performance. Connect the AC adaptor and speakers AC adaptor -mV i Power cable Indicator to AC outlet To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and turn off the power on all devices before making any connections. Stereo Headphones Amplified speakers, etc. To prevent the inadvertent disruption of power to your unit (should the plug be pulled out accidentally), and to avoid applying undue stress to the AC adaptor jack, use cable ties to fasten the cord from the AC adaptor to the stand. If you're working in mono, only use the L/MONO jack. This completes assembly and connections. ■ When you've finished making connections, turn on the power as described in the TD-4 Owner's Manual, and verify that you can hear sound. Detailed explanation of each part ■ KD-8 (Kick) Use a commercially available kick pedal. To prevent damage to the floor or carpet and to ensure stability, we recommend that you use a drum mat (TDM series; sold separately). A NOTE * Install the kick pedal securely. * Take care not to pinch your fingers. * The tips of the anchor bolts are sharp. Handle with care. * When moving the KD-8, be sure to remove the screws and fold the stand. Transporting the KD-8 while it remains open may subject the stand to excessive strain and result in damage to the stand. * Anti-skid tape is affixed...