Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
.. FOR LARGER BABY: Use upper harness slots and the end strap loops ... CHECK that the loops are completely within junction plate slots ... CHECK that straps are secure by pulling on them. 28 .... 5.2 Securing Child in Infant Restraint Failure to properly secure your child in the infant restraint/carrier increases the risk of serious injury or death from suffocation or falls, or in the event of a sudden stop or crash. Even when used only as a carrier, make sure the harness straps are properly secured. 1. Move infant restraint handle to sitting position (see page 11). 2. Open harness clip by . squeezing both sides and unbuckle as shown ... OR 3. Place your child in the infant restraint as shown in .., not ... Pull the harness straps down over your child. 4. Follow directions for your harness: 5.2.1 3-Point Harness: p. 30 5.2.2 5-Point Harness: p. 31 .... 29 5.2.1 3-Point Harness 5. Buckle harness to the latch between child’s legs. Make sure that you hear a “click.” DO NOT use the infant restraint if the harness does not latch in place. Call Graco at 1-888-224-6549. 6. From the back, pull strap through harness tightener to tighten the straps as shown ... CHECK that both straps are flat and tight on child’s shoulders. 7. Snap harness clip pieces together ... Position harness clip in middle of chest, . level with armpits and away from the neck ... 8. SAFETY CHECK: a) CHECK that harness straps are not twisted. b) CHECK that the harness is snug. You should not be able to insert more than one finger between the harness and your child’s shoulder ... .. .. 30 5.2.2 5-Point Harness 5. Insert the two buckle tongues into the harness buckle on the crotch strap. Make sure that you hear each tongue click into the buckle. DO NOT use the infant restraint if the .. harness does not latch in place. Call Graco at 1-888-224-6549. 6. Snap harness clip pieces together ... 7. Pull on harness adjustment strap to tighten straps as shown ... CHECK that both straps are flat and tight on shoulders. 8. level with armpits and away from the neck ... 9. SAFETY CHECK: a) CHECK that harness straps are not twisted. your child’s shoulder ... 31 Position harness clip in middle of chest, b) CHECK that the harness is snug. You should not be able to insert more than one finger between the harness and .... 5.3 Installing the Infant Restraint/Base Using Vehicle Belt You must carefully follow the instructions provided by your vehicle manufacturer, in addition to the information in this manual. Be sure you have read and understood section 4, “Infant Restraint Location” on p.19-23. Make sure vehicle is on level ground so that the level indicator, which is attached to the infant restraint, can be used to properly recline the infant restraint ... If a front passenger seat is used, slide the vehicle seat rearward as far as possible from the dashboard. If a rear seat is used, make sure the seat in front of it is moved forward enough and is upright enough to allow room for the infant restraint. 1. Remove infant restraint from base, regardless of whether or not you plan on using the base. 2. Place the base . or infant restraint without base ....in a rear-facing position in a forward-facing vehicle seat. .. 32 .... 3. Thread the seat belt: Belt MUST go Base with seat belt under tongue Infant restraint with seat belt 4. Buckle the seat belt. Make sure the buckle tongue goes into the correct buckle ... The seat belt should not be twisted or turned. .. 33 5. Tighten the vehicle seat belt. Refer to your vehicle owners manual and the instructions in “4.2.2 SAFE Vehicle Belt Systems”, p. 22-23, on tightening your vehicle belt. To create a very tight installation, push down hard with your knee or free hand in the middle of the infant restraint or base . and pull and tighten the vehicle belt. .. 6. Push the infant restraint down into the base and make sure that you hear a “click” ... Pull up on the infant restraint to be sure it is latched securely into the base. If the infant restraint does not securely latch into the base, the infant restraint provides NO protection for your child. DO NOT use the infant restraint/base if the infant restraint does not securely latch into the base. .. 34 ................ 5.4 Using LATCH to install Base 1. For ease of installation, extend LATCH Tongue to its maximum length. 2. Position base in vehicle seat as shown. 3. Thread LATCH through base belt path normally used for vehicle seat belt. Make sure that LATCH is UNDER tongue on base ... Belt must lay flat and not be twisted. 4. Hook Connectors to vehicle lower anchors. Pull firmly on Connectors to be sure they are attached ... 5. Tighten LATCH by pushing down hard on base and pulling the adjustment belt ... 6. NEVER put two LATCH connectors on one vehicle LATCH anchor unless specifically allowed by the vehicle manufacturer ... 7. Test infant restraint for secure installation as described in infant restraint “Final Safety Check” p.38. 8. Check that the LATCH stays tight and does not ...
Эта инструкция также подходит к моделям:Детские коляски - 6111 (3.76 mb)
Детские коляски - 6118 (3.76 mb)
Детские коляски - 6316 (3.76 mb)