Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
* iTunes and iPod are trademarks of Apple, Inc., registered in the U.S.A. and other countries. GENERAL CONTROLS 1. Power Cable: This power cable should be plugged into a wall receptacle AFTER all audio connections are made. 2. RCA Audio Output Cables: These cables should be plugged into a CD or Auxiliary LINE input. This output should be connected to your receiver, home stereo, or other speaker system. IMPORTANT WARNING: The RCA cables are LINE level. Please only connect these cables to LINE level inputs. You may damage your receiver if you plug in a LINE level into a PHONO input. 3. USB Audio Output: Use the included USB Cable to connect your turntable to your computer. For transferring your vinyl records to your computer, we have provided two different software packages on the included CD. 4. 1/8” Stereo Line Input: Connect Tape Players, Reel to Reel, or any other audio source here. This signal is sent to the computer through the USB. Make sure that your phono cartridge is installed while using this input for maximum sound quality. Also make sure that your RCA jacks are either plugged into an input device or not in contact with metal. Note: The 1/8" audio input is not routed to the turntable's RCA output jacks, only to your computer via USB. 5. Tonearm: The tonearm can be raised and lowered by hand, or by pressing the Raise/Lower button. 6. Platter: Put the record you would like to play on this platter. 7. 45 RPM Adapter Holder: Holds the included 45 RPM adapter. When not using the adapter, please place it in this holder. 8. Raise/Lower Button: Press this button in to raise the tonearm. To lower the tonearm, press this button so it is in the out position. 9. Stop: Press this button to stop playback. When this button is pressed, the tonearm will return back to its original resting position. 10. Speed 33/45 RPM: This button controls the playback speed of the record. Depending on what kind of record you are playing, you will need to adjust the speed to match the speed of the record (or else the music might sound too slow or too fast). ATTACHING THE DRIVE BELT The ION TTUSB05XL platter is driven by a rubber drive belt attached to the turntable motor. In some rare cases, this belt may slip off, causing the turntable platter to stop spinning. If the turntable does not begin spinning when you lower the tonearm, the most likely cause is the belt. Please follow the instructions below in order to properly re-attach the belt to the motor and the platter. 1. Begin by removing the clip which secures the platter to the center spindle. After you have removed the clip, remove the platter. 2. Turn the platter upside down. Place the rubber drive belt around the inner bottom ring of the turntable platter, making sure that the rubber belt is not twisted. 3. Place the platter back onto the center spindle and rotate it so that you can see the motor spindle through the hole on the platter. Now reach into the hole, pull the rubber drive belt off the inner ring and install it over the motor spindle, as shown in the illustration. Be careful not to twist the belt during this step. 4. Lastly, replace the clip onto the center spindle to secure the platter IMPORTANT Make sure that the rubber grip mat is always placed on top of the platter while using the turntable. Failure to use the grip mat may cause damage to your media as well as damage to the turntable. Remove the plastic cartridge cover (needle cover) before operating the turntable. BEFORE RETURNING THE PRODUCT, please contact ION Audio or your retailer for technical support. Contact information can be found in the Safety Instruction Booklet included with this product. 1 (ESPANOL) MANUAL DE COMIENZO RAPIDO DEL LECTOR (ESPANOL) MANUAL DE COMIENZO RAPIDO DEL LECTOR 1. Asegurese de que todos los articulos incluidos al inicio de este manual estan incluidos en la caja. 2. LEA LAS INSTRUCCIONES DEL FOLLETO DE SEGURIDAD ANTES DE UTILIZAR EL PRODUCTO. 3. Visite para registrar el producto. INTRODUCCION El giradiscos USB se conecta directamente a su computadora para convertir sus valiosos vinilos en musica digital. Hemos incluido dos paquetes de software para ayudarle a convertir sus grabaciones de vinilo: • EZ Vinyl/Tape Converter (PC solamente) es la forma mas rapida y facil de convertir las grabaciones en medios digitales. Este software guarda convenientemente sus grabaciones en la biblioteca de iTunes. Es posible que los usuarios novicios prefieran esta aplicacion. Incluidos una practica Guia de inicio rapido con instrucciones paso a paso sobre la instalacion y la operacion del software. • EZ Audio Converter (Mac unicamente) es una aplicacion de convertidor basica para Mac OS X, ideal para usuarios novicios. Consulte en la Guia de inicio rapido del software incluida las instrucciones detalladas sobre la instalacion y la operacion del software. Para instalar el software: inserte simplemente el CD incluido en la computadora y siga las instrucciones de la pantall...