Оценок - 0, средний балл: 0
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention. If you have long nails, do not open the battery cover by using your finger. Or else, your nail could break. >Caution Getting Started 9 Getting Started 1 ARemote sensor BLED indicator You can check the current state of the sound bar by the colour LED on it. Refer to the table below. Front panel AB LED Colour LED State Red Orange Green White Off Power on or disconnected power cord On Standby --- Blink ( Twice per second) Booting Bluetooth ready - LG sound sync (LG TV ) ready Blink (Once per second) Mute --- On -> Off (After 3 seconds) -Bluetooth paired Optical function selected LG sound sync (LG T V ) paired 10 Getting Started 1 Rear panel Getting Started EFDABC A F (Function) Press it repeatedly to select other function. B o/p( Volume) Adjusts speaker volume. C 1/! (Standby/On) D Foot stand E Optical input F DC input >Caution Precautions in using the touch buttons • Use the touch buttons with clean and dry hands. -In a humid environment, wipe out any moisture on the touch buttons before using. • Do not press the touch buttons hard to make it work. -If you apply too much strength, it can damage the sensor of the touch buttons. • Touch the button that you want to work in order to operate the function correctly. • Be careful not to have any conductive material such as metallic object on the touch buttons. It can cause malfunctions. Getting Started 11 1. Detach the foot stand from the main unit. Mounting the main unit on a wall Mounting the main unit on a wall, you should 1 connect all the cables for operating the unit. For details, refer to the page 13. 2. Put the shafts on the bottom of the main unit and fix it firmly by using the screws that have been loosened on step 1. You can mount the main unit on a wall. Prepare screws and brackets. 3. Match the TV’s BOTTOM EDGE of Wall bracket install guide with the bottom of TV and attach Getting Started Main unit to the position. TV Shaft for wall Wall bracket mount Wall bracket install guide Detach the unit from the bracket as shown below. , , 12 Getting Started 1 4. When you mount it on a wall (concrete), use the 7. Hang the main unit onto the bracket as shown wall plugs (Not supplied). You should drill some below. holes. A guide sheet ( WALL BRACKET INSTALL GUIDE) is supplied to drill. Use the sheet to check the point to drill. >Caution Getting Started Screws and Wall Plugs are not supplied for mounting the unit. We recommend the Hilti (HUD-1 6 x 30) for the mounting. Please purchase it. , Note 5. Remove the Wall bracket install guide. 6. Fix it with screws (not supplied) as shown in the illustration below. TV Make sure that the arrow mark on the wall bracket should be facing upwards. , Note • Do not install this unit upside down. It can damage the parts of this unit or be the cause of personal injury. • Do not hang onto the installed unit and avoid any impact to the unit. • Secure the unit firmly to the wall so that it does not fall off. If the unit falls off, it may result in an injury or damage to the product. • When the unit is installed on a wall, please make sure that a child does not pull any of connecting cables, as it may cause it to fall. Note After connecting all the cables, hide the connector with the cover on the unit. , , Connecting 13 Connection and setting OPTICAL In connection Connect the OPT. IN jack on the back of the unit up to OPTICAL OUT jack on the TV using an OPTICAL cable. Connecting the AC adapter 1. Connect the supplied AC power cord to the AC adapter. 2. Connect the AC adapter cable to DC. IN adapter Connecting 2 input. 3. Plug the AC power cord into an AC outlet. Note >Caution Only use the AC adapter supplied with this device. Do not use a power supply from another device or manufacturer. Using any other power cable or power supply may cause damage to the device and void your warranty. 14 Connecting 2 Connecting Pairing wireless subwoofer Setting up the wireless subwoofer for the first time 1. Connect the power cord of the wireless subwoofer to the outlet. The yellow-green LED on the subwoofer starts to blink. 2. Turn on the sound bar. The red LED on it starts to blink and then the sound bar and the subwoofer will be automatically connected. Manually pairing wireless subwoofer When the connection has been failed between the sound bar and the wireless subwoofer, the red LED on the subwoofer is turned on. To pair them, follow the steps below. 1. Press PAIRING on the back of the subwoofer. The yellow-green LED on the wireless subwoofer starts to blink. 2. Press and hold p ( Volume) on the unit and i(Mute) on the remote control at the same time. The green LED on the sound bar starts to When connection is completed, the yellow-blink. green LED on the subwoofer is turned...