Оценок - 2, средний балл: 4 ( )

Производитель: Kenwood Размер: 2.05 mb Название файла: Язык инструкции:

2 Press the 6 key. 3 Wait a few seconds, and ensure that the display is as shown below. 4 Wait for a few seconds then turn power off. C cDNo. Dis IN MOST CASES IT IS AN INFRINGEMENT OF COPYRIGHT TO MAKE COPIES OF TAPES OR DISCS WITHOUT THE PERMISSION OF THE COPYRIGHT OWNERS. ANYONE WISHING TO COPY COMMERCIALLY AVAILABLE TAPES OR DISC SHOULD CONTACT THE MECHANICAL COPYRIGHT PROTECTION SOCIETY LIMITED OR THE PERFORMING RIGHTS SOCIETY LIMITED. WARNING NOTICE: Manufactured under license from Dolby Laboratories. “DOLBY”, the double-D symbol and “PRO LOGIC” are trademarks of Dolby Laboratories. Knowledge section XD-SERIES (EN/M,T) 65In case of difficulty What seems to be a malfunction is not always so. Before calling for service, check the following table according to the symptom of your trouble. XD-SERIES (EN/M,T) 65In case of difficulty What seems to be a malfunction is not always so. Before calling for service, check the following table according to the symptom of your trouble. Operation to reset Unplug the power cord from the power outlet then, while holding the ENTER key depressed, The microcomputer may fall into malfunction (impos plug the power cord again. sibility to operate, erroneous display, etc.) when the power cord is unplugged while power is ON or due to (Main unit only) an external factor. In this case, execute the following ENTER procedure to reset the microcomputer and return it to normal condition. O Please note that resetting the microcomputer clears the contents stored in and returns and to condition when it left the factory. Receiver, speakers Symptom Cause Remedy Sound is not produced. O The speaker cords are disconnected. O The MUTE switch of remote control unit is switched ON. O The headphone plug is inserted into the jack. O Connect properly referring to “System connection”. O Switch MUTE OFF. O Unplug the headphone plug. 8 9 . . No sound is produced from the super woofer. (XD-7...series only) O The SUPER WOOFER key is set to off. O Press the SUPER WOOFER key to on. . “STANDBY” and “TIMER” indicators blink alternately and no sound is output. O The speaker cords are short-circuited. O Turn the power OFF, remove the short- circuit and turn the power ON again. Sound is not produced from the left or right speakers. O The speaker cords are disconnected. O The left and right volumes are not balanced. O Connect properly referring to “System connection”. O Adjust the left and right volume balance. 8 9 p “Dolby Pro logic” and O The center speaker and surround O Perform the center speaker and sur-Y “Dolby 3 stereo” cannot be speakers are set to “No”. round speaker setting operations prop- selected. (XD-6...series, XDerly. 8...series only) The clock display blinks. O There was a power failure. O The power cord was unplugged from the outlet. O Adjust the present time again. O Adjust the present time again. I I Timer operation is not possible. O The present time has not been adjusted or there was a power failure. O The timer program or the timer ON/ OFF time has not been set properly. O Adjust the present time referring to “Clock adjustment”. O Check the timer program and set its ON/ OFF time properly. Note that“Everyday” and “One Time” cannot be set simultaneously for a single timer program. I I Radio stations cannot be reO The antennas have not been conO Connect antennas.7 ceived. nected. O A proper broadcasting band has not been selected. O The frequency of the station to be received is not tuned. O Select a band. O Tune to the frequency of the desired station. . . Noise interferes. O Car ignition noise. O Influence of an electric appliance. O A TV set is installed near the system. O Install the outdoor antenna in an apart position from the road. O Switch the suspected electric appliance OFF. O Install the TV or the system at an increased distance between them. 8 Knowledge section 66 In case of difficulty 66 In case of difficulty XD-SERIES (EN/M,T) No station can be received by preset call operation. O The frequency of the preset station is not tunable. O The preset memory has been cleared because the power cord has been unplugged for a long period. O Preset stations with tunable frequencies. O Preset stations again. U U Demonstration starts suddenly. O The power plug was unplugged from the outlet while the power switch was ON, or there was a power failure. O This is not malfunction. Press the DISPLAY/DEMO key to cancel the demontration. \ 6 Power turns OFF in the middle of operation. O “A.P.S. on” is set. O Set the “A.P.S. off”. a “Tape Dubbing” is not displayed in the menu. (XD-6...series, XD-8...series only) O The DSP play or surround play pattern is selected. O Select other equalizer pattern than the DSP play and surround play patterns. E Cassette deck Symptom Cause Remedy Sound cannot be produced O The head is dirty. O Clean the head referring to “Maintea by pressing the play key. O The tape is wound too tight due to irregular winding. O A nonrecorded tape is played. nance”. O Try another tape...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: