Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
This direction is the direction stored in memory when the tape was last stopped. Transport direction indicators 2 3 22 23Playback of tape 23Playback of tape To wind tape at high speed To fast wind in To fast wind in direction | direction \ 4 . O Press the 7STOP key to stop fast winding. Selection of TAPE equalizer (TAPE EQ.) (Remote control unit only) TAPE EQ. TAPE EQ. When playing a tape prerecorded with Noise Reduc- tion system (such as the DOLBY NR) ON, be sure to set the "TAPE EQ." ON for playback. Each press switches the modes as follows. 1“TAPE EQ.” ON TAPE equalizer is used. 2“TAPE EQ.” OFF TAPE equalizer is not used. Lit when “TAPE EQ.” is ON O Select the "TAPE EQ." ON mode according to the recording condition of the tape. T0000APESTOPRW O Normal (TYPE ), high (TYPE ), or metal (TYPE selection is set automatically. ) tape O Remove tape slack before loading. Tape counter T0152APEPLAY Reverse mode indication Displayed when the deck is loaded with a tape. Transport direction indicators To stop playback STOP 7 Selection of reverse mode (Main unit only) 1Select “TAPE RVS. ?”. menu volume/ multi control up set/demo down (Press the set/demo key while the “?” mark is blinking.) 2Select. volume/ multi control up down 1 “ ” : (REVERSE) Both sides are played back (recorded), and then the tape stops. 2 “ ”:(ENDLESS) Both sides are played back endlessly. (The tape stops after recording onto both sides.) 3 “ ”: (ONE-WAY) Only one side is played back (recorded), and then the tape stops. (The initial setting is " " (REVERSE). 3Set it. set/demo A tip for use of the tape counter The tape counter is set to “0000” when a cassette tape is loaded. By writing down the counter reading in case you want to interrupt recording (playback) in the middle of the tape, the memo will be helpful as a reference for locating the same position when continuing the recording (playback) the next time. The tape counter figure decrements during recording or playback of the back side (while the 2 tape transport indicator is lit). To set the tape counter to “0000”, open the cassette holder once. Then the counter will be reset. Do not use a cassette with more than 90-minute recording time, for the tape used with such a cassette is very thin and tends to cause troubles such as entanglement around the pinch roller or cutting of tape. Basic section 24 Receiving broadcast station 24 Receiving broadcast station When the “TUNER/band” key is pressed, the unit will automatically be switched on and reception status will be reached. Up to 40 radio stations can be preset in memory. Collective presetting of stations Auto/manual station switching Preset call One-by-one presetting 11 3 Basic section TUNER/band 11 1. Press the tuner/band key. Preset a radio station in memory. 1FM 2AM 2. Preset a radio station in memory (auto preset). Follow the procedure in "Collective presetting of stations (auto preset)" to preset automatically the tunable radio stations in your area. ¤ . Once stations are stored by auto preset, the present procedure is not required from the next time, unless you move of house or re-execute presetting of all tunable stations. 4 . 3. Tuning (Preset Call) O If radio stations have already been stored with auto preset or manual preset, 33 select a station using the 4P.CALL. key. Each press of the same key switches the preset stations in sequence. When . is pressed: 1=2=3 ... 38=39=40=1... When 4 is pressed: 40=39=38 ... 3=2=1=40... O To select a preset station from the remote, use the 4P.CALL. key or numeric keys. When no stations have been memorized TUNING Auto tuning : The next broadcasting station will be received automatically each time this key is pressed. Manual tuning : Press the 1TUNINGA key repeatedly until a station is received. Or hold either key and release it when the frequency of the desired station is received. 25Receiving broadcast station 25Receiving broadcast station One-by-one presetting(manual preset) 1Press the ENTER key during reception. ENTER AUTO MFM87.50MHzEMORYP-- “MEMORY” lights (for approx. 20 sec.) (Proceed to step 2 while “MEMORY” is lit.) 2Select one of the preset numbers from 1 to 40. P.CALL contents. 3Press the ENTER key again. ENTER (Repeat steps 1,2,3 to preset other stations) Reception band indication AUTO TFM87.50MHzUNERP-- The “TUNED” indicator lights when a station is received. O A maximum of 40 stations of the band presently being received will be preset. O If several stations are preset under the same number, the previous memory is replaced with the latest memory Tuning mode switching and reception mode (Remote control unit only) PGM Each press alternates the mode. 1 “AUTO” lit (Auto tuning, stereo reception) AUTO/MONO 2 “AUTO” not lit (Manual tuning, monaural reception) Use the manual tuning mode when reception is noisy due to weak reception. (In the manual mode, stereo broadcasts are received in monaural.) . Normally, use the AUTO (Auto tuning, stereo reception) mode. Basic section AUTO TUNED TFM87.50...