Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
“A” Channel “B” Channel T6: 171.105 MHz T7: 171.845 Pinnacle 2 CoNTRoL PANEL: sw225 voice Projector HANDLE AMPLIFIER CONTROL PANEL BATTERY DOOR PANEL MAIN POWER SWITCH The MAIN POWER switch is located on the control panel. Flip the rocker switch to the ON position. The red light next to the switch will light up showing that the power is on. DC INPUT Connection for an optional external power adapter. AUX OUT Power source for 12 to 15V DC accessories. MASTER VOLUME Controls the volume level of the microphones, including the wireless microphones. MICROPHONE INPUTS There are three microphone inputs, which can be used simultaneously: DYNAMIC - for standard dynamic microphones, 1/4 in. CONDENSER -for electret or condenser microphones, which require phantom power (supplied from the amplifier) 3.5 mm WIRELESS -accepts output from an external wireless microphone receiver AUXILIARY The LINE IN provision is for connecting an external audio source such as a CD player, tape player, MP3 player or computer sound card This input also serves as a provision for connecting additional wireless microphone receivers, audio mixers and other line level audio sources. Separate VOLUME and TONE control knobs allow flexibility in controlling the sound quality as well as balancing the auxiliary source with the microphones. OUTPUT The LINE OUT provision may be used for connecting to an input on a recording device, such as a computer sound card, MP3 recorder, tape recorder, or similar device. The LINE OUT can also be used for a number of other applications, such as connecting to a house system, or connecting to one of our wireless speaker transmitters, for example. EXTERNAL SPEAKERS Two separately amplified speaker jacks allow you to use one or two S1201, S1290, or any of our horn speakers for additional sound power. Note: when using a stereo AUX source with a single speaker, only one of the stereo channels will be heard. However, all MIC inputs are heard equally on both channels. INTERNAL WIRELESS MIC RECEIVER MAIN POWER SWITCH POWER INPUT AUX OUT MASTER VOLUME MICROPHONE INPUTS AUXILIARY VOLUME LINE IN TONE CONTROL SPEAKER JACK LINE OUT **CONNECT S1670 HERE SPEAKER JACK RF INTERFERENCE Please note that wireless frequencies are shared with other radio services. According to the Federal Communications Commission regulations, “Wireless microphone operations are unprotected from interference from other licensed operations in the band. If any interference is received by any Government or non-Government operation, the wireless microphone must cease operation…” If you need assistance with operation of frequency selection, please contact your dealer or AmpliVox. Additionally There are models available for use in Canada. POWER SOURCE The transmitter and receiver are each operated by a 9V alkaline battery. Before use, install a battery as shown. Make certain the battery is fully seated in its compartment so the cover slides in place easily. Battery life with alkaline batteries is approximately 8 hours of operating time. The receiver also features an external jack for connecting a 9V DC power supply (not included). POWERMICROPHONEAUXILIARYOUTPUTFREQ PWR INTERNAL WIRELESS RECEIVER ON A B OFF ON ON OFF ON DC IN AUX OUT CONDENSER WIRELESS DYNAMIC VOLUME VOLUME LINE IN TONE SPEAKERS LINE OUT L R MADE IN USA 1-800-267-5486 WWW.AMPLI.COM AMPLIVOXEXTEND YOUR VOICE WITH PORTABLE SOUND SYSTEMS s w 2 2 5 Pinnacle 3 TRANSMITTER OPERATION HELPFUL HINTHELPFUL HINTS If there is a “dead spot” in a room, try a slight change of position or try changing frequencies. Each unit provides two selectable transmitting frequencies. 1) Switch the Frequency Selector Switch to the desired channel (A or B). 2) Belt clip on the back of the unit clips the transmitter onto a belt or the transmitter simply can be put into a pocket. 3) Plug the microphone into the Mic Input Jack. 4) The microphone can be clipped to a necktie or other clothing, using the supplied clip. 5) Slide the power ON/OFF switch to the ON position (the LED indicator light will illuminate). THE CHANNEL SELECTOR SWITCH HAS A OR B CHANNEL MAKE SURE THAT THE AMPLIFIER IS ON THE SAME CHANNEL FOR THE MIC TO WORK transmitter Features MIC INPUT JACK POWER ON INDICATOR POWER ON/OFF SWITCH CHANNEL SELECTOR SWITCH A) If the selected channel is noisy, switch both the transmitter and receiver to the other channel. C) Low ceiling fluorescent lighting, overhead telephone lines, or close proximity to metal fences can all cause static. If this occurs, try a slight change of position and/or try changing frequencies. D) When the battery voltage drops below 6V, the LED indicator will go out. This means you need a new battery. E) Be sure to turn off the power whenever the units are not in use, and remove the batteries if the units will be out of service for a long time. F) Cellular telephones cause interference with the wireless mic. Please ask your audience to turn off their cell phones. NOTE: There are no user-adjustable parts...
Эта инструкция также подходит к моделям:Музыкальные центры - ST3240 (277.74 kb)