Оценок - 0, средний балл: 5
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
•This unit may pick up interference from a radio if there is one nearby. Keep radios as far as possible from this unit. Turn balance weight Center line .... Earth lead Audio mixer Adjusting the height of the insulators Place the unit where it is to be used and adjust the height of the legs to make the unit horizontal. Preparatory adjustments Horizontal balance and stylus pressure 1 Release the tone arm. 1. Remove the stylus cover, taking care not to damage the stylus, then release the arm clamp. 2. Free the tone arm from the arm rest. Arm clamp 2 Adjust horizontal balance 1. Push the cue lever down. 2. Turn the anti-skating control to “0”. 3. Turn the balance weight until the arm is approximately horizontal. Take care at this time not to allow the stylus to touch the unit. ........Arm clamp Arm rest Cue lever Anti-skating control Balanced Too far forward Too far back 3 Turn the stylus pressure control to “0” 1. Return the tone arm to the arm rest and fix it with the arm clamp. 2. Turn the stylus pressure control to “0”. Hold the balance weight still while doing this. Balance weight Center line Turn stylus pressure control Arm clamp 4 Adjust stylus pressure Turn the balance weight to adjust to the appropriate pressure for the cartridge you are using. See the cartridge’s instructions for recommended stylus pressure. The stylus pressure control will turn at the same time. Stop when the center line points to the required pressure. 6 RQT7018 RQT7018 7 Preparatory adjustments Using the balance weight control Make note of the balance weight setting for your stylus cartridge, you can quickly change the stylus pressure without having to readjust the horizontal balance of the arm each time you remove and re-attach the stylus cartridge. Attach the cartridge to the tone arm you are using. Turn the balance weight control to the setting you previously used to balance the weight including cartridge. Turn the stylus pressure control dial to the setting you previously used to balance the weight including cartridge. Anti-skating Adjust the dial to the same value as the stylus pressure control when playing normal music. For scratch play Adjust the control to reduce skipping. Armlift height Preparation 1. Put a record on the turntable. 2. Take off the stylus cover and release the arm clamp. Use a screwdriver to turn the armlift screw. Make this adjustment only if the cartridge you are using makes it necessary. •Turning the screw clockwise lowers the armlift. •Turning the screw anti-clockwise raises the armlift. Armlift height (the distance between the record and stylus when the cue lever is raised) is set to between 8 and 13 millimeters at time of shipment. Tone arm height 1. Release the arm lock. 2. Adjust the arm height. •Adjust the ring using the chart below as reference so the arm height matches the indicated height of the cartridge. Measurements are marked on the arm height control ring in 0.5 millimeter intervals. Index line Fit the dust cover Hold the dust cover with both hands and fit it over the player from directly above. •If you do not know the height of your cartridge, rest the stylus on a record and adjust the height control until the tone arm and record are parallel. 3. Lock the arm after adjusting the height. Armlift screw Armlift 1 Locked3 Released Arm height control ring Tone arm and record parallel. Balance weight measurement units Cartridge height (H) in millimeters 17 18 19 20 21 22 23 Height control position 0 1 2 3 4 5 6 RQT7018 8 When the player is to be used for scratch play. Use the disc slip sheet instead of the turntable mat. This enables the record to be easily moved during play. •Top (printed side): Lay the record on this side. •Bottom: Slippery side. For a different kind of slip Put the transparent sheet under the disc slip sheet. Playing records Preparation 1. Put a record on the turntable. 2. Take off the stylus cover and release the arm clamp. 1 Turn [power] to turn the unit on. •The pilot lamp comes on. •33 1/3 r/min is automatically selected and the indicator lights. •Press [45] if you are playing a 45 r/min record. 2 Press [start-stop]. The turntable starts revolving. 4 Lift the cue lever and move the tone arm over the record. 5 Lower the cue lever. The tone arm moves down and play starts. 3 Press [reset] to light the pitch control green LED lamp. The pitch returns to 33 1/3 or 45 r/min. Use the above indicated pitch for playing standard music. To temporarily stop play Lift the cue lever. The stylus lifts off the record. Refer to page 9 for fine adjustments to the pitch When using EP records 1. Take the EP record adaptor out of its holder and fit it over the center spindle. 2. Press [45] to change the speed. When play finishes 1. Lift the cue lever and move the tone arm back to the arm rest. 2. Press [start-stop]. The electronic brake gently stops the turntable. 3. Turn [power] to turn the unit off. 4. Clamp the tone arm and put the stylus cover back on. To light up the stylus •Press the sty...
Эта инструкция также подходит к моделям:Музыкальные центры - SL-1210MK5 (750.53 kb)
Музыкальные центры - SL-1200MK5 (750.53 kb)