Оценок - 3, средний балл: 4.7
(
)
)
|
Фрагмент инструкции
From backside of drawbar place reinforcement plate so that weld screws go through holes in left side of drawbar. Place support tube over weld screws and assemble flat washer, lockwasher, and wing nut as shown Do not tighten at this time. 4. Discard remaining hex bolts and locknuts in hardware GROUP "A". REINFORCEMENT UPPER CORNER RIBS LOCK WING NUTS 02352 LANCED TABS SELF TAPPING SHOULDER PLATE SUPPORT TUBE FLAT WASHERS WASHERS BOLTS TOWARD BOTTOM FIG. 1B DRAWBAR WITHOUT UPPER CORNER RIBS - STY LE "B" (See Fig. 1C) 1. Assemble the mounting bracket, lanced tabs towards bottom, using the four smaller inside holes on the drawbar. 2. Install the four hex bolts and locknuts as shown and tighten securely. 3. Assemble the support tube to drawbar as shown. From backside of drawbar place reinforcement plate so that weld screws go through holes in left side of drawbar. Place support tube over weld screws and assemble flat washer, lockwasher, and wing nut as shown Do not tighten at this time. 4. Discard remaining shoulder bolts in hardware GROUP "A". REINFORCEMENT HEX BOLTS LOCK WING NUTS LANCED TABS TOWARD BOTTOM PLATE SUPPORT TUBE FLAT WASHERS WASHERS LOCKNUTS FIG. 1C 7 8 02092 02086 SUPPORT POST (See Fig. 3) Use Hardware - - GROUP "B" 1. Rotate cover assembly onto its side as shown. 2. Assemble support post to container support with the three (3) carriage bolts and locknuts. Tighten securely. ALIGNMENT MARKS COVER SEAL FIG. 2 COVER SEAL (See Fig. 2) No hardware required 1. Align mark on seal with mark at cover opening. 2. Work seal into opening so cover sits between fl anges of seal. 2 3 LOCKNUTS CARRIAGE BOLTS SUPPORT POST FIG. 3 MOUNTING TO TRACTOR (See Fig. 4) Use Hardware - - GROUP "C & D" NOTE: For ease of assembly, you may wish to obtain the as sis tance of another person for mounting assembly to tractor. 1. Raise seat on tractor to allow assembly to be mounted. 2. With cover closed, lift assembly and place support post inside mounting bracket. Allow assembly to rest on lanced tabs of mounting bracket. 3. Line up holes in mounting bracket with holes in support post and insert bracket support pin. Secure with retainer spring. 4. Unlatch and open cover. 5. Secure cover assembly to support tube using short hex bolt, long hex bolt, and locknuts as shown. Tighten all hardware securely. NOTE: Hardware securing support tube to drawbar must be tightened at this time. 6. Install the four (4) tubing end caps onto container support. Tap each end cap onto container support tubes to seat securely. 4 02090 RETAINER SPRING LANCED TABS COVER ASSEMBLY FIG. 4 LOCKNUTS END CAP SHORT HEX BOLT LOCKNUTS BRACKET SUPPORT PIN LONG HEX BOLT SHORT HEX BOLT LONG HEX BOLT SUPPORT TUBE SUPPORT POST MOUNTING BRACKET 9 WARNING Donotoperatemowerunlesscontainerisproperlyis subjecttowearanddetierioration.Check bagfrequently.Replacewhen crackedordamaged.Useonlya recommendedreplacementcontainer. WARNING 02082 CONTAINER MOUNTING (See Fig. 6) No hardware required 1. Install one container to left side fi rst with warning to outside of unit. Install other container to right side. NOTE: Right con tain er should always over lap left con tain er at center sup port. 2. Close cover and lock latch handle over center support tube. 6 CENTER SUPPORT TUBE COVER LATCH HANDLE CONTAINER HANDLE CONTAINER WARNING FIG. 6 CONTAINER WARNING CONTAINER ASSEMBLY (See Fig. 5) No hardware required 1. Place bottom half inside of top half, as shown. 2. Place one foot inside bottom half and lift top half to meet bottom half. 3. Press halves tightly together while lifting top to lock into place as shown. IMPORTANT: BEFORE LOCKING THE TABS, HOOKED EDGES ON BOTH HALVES MUST OVERLAP TO FORM SEAL AS SHOWN IN INSET. 4. Repeat for other containers. PRESS TOGETHER TO FORM SEAL WHILE LIFTING TOP HALF 02089 CONTAINER BOTTOM HALF CONTAINER TOP HALF ASSEMBLY CHECK: Squeeze sides of lower half of contain er and check that there is no gap between upper and lower halves. If a gap appears, unlock tabs to separate container halves and repeat instructions above. LOCKING TAB WARNING Donot operatemowerunlesscontainerisprope rlyissubjecttowearanddetierioration.Checkbagfrequ ently.Replacewhencrackedordamaged.Useonlyarecomme ndedreplacementcontainer. 02097 FIG. 5 5 02739 CONTAINER BOTTOM HALF CONTAINER TOP HALF LOWER CHUTE (See Figs. 7A & 7B) Use Hardware - - GROUP "E" 1. Press weld nut into rubber latch and install two latch hook assemblies to lower chute using screw, washer, and lock washer as shown. 2. Tighten hardware securely. 3. Raise and hold deflector shield in upright position. 4. Place rear of chute over rear of mower deck opening. Push chute down and forward to guide extended edge of chute between discharge guard and mower deck. 5. Hook front latch into tab hole on front of mower deck. 6. Hook rear latch into flange hole on back of mower deck. WELD NUT CAUTION: Do not remove discharge guard from mower. Raise and hold guard when at tach ing lower chute and allow it to rest on chute while...
Эта инструкция также подходит к моделям:Газонокосилки - 156239 (868.82 kb)